Gerardo Pelaez

Prof. Dr. Gerardo Pelaez

Mechanical Engineering, Universidade de Vigo, Vigo, Galicia, Spain
orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2018 in Sensors
Verified
Journal Article
Open access
PDF file
Gerardo PelaezGerardo Pelaez
Gerardo Pelaez
JVJoshua Vaugan
Joshua Vaugan
PIPablo Izquierdo
Pablo Izquierdo
Higinio Rubio AlonsoHiginio Rubio Alonso
Higinio Rubio Alonso
JGJuan Carlos García-Prada
Juan Carlos García-Prada
Input shaping is an Optimal Control feedforward strategy whose ability to define how and when a flexible dynamical system defined by Ordinary Differential Equations (ODEs) and computer controlled would move into its operative space, without command induced unwanted dynamics, has been exhaustively demonstrated. This work examines the issue of Embedded Internet of Things (IoT) Input Shaping with regard to real time control of multibody oscillatory systems whose dynamics are better described by differential algebraic equations (DAEs). An overhead crane hanging a double link multibody payload has been appointed as a benchmark case; it is a multibody, multimode system. This might be worst scenario to implement Input Shaping. The reasons can be found in the wide array of constraints that arise. Firstly, the reliability of the multibody model was tested on a Functional Mock-Up Interface (FMI) with the two link payload suspended from the trolley by comparing the experimental video tapping signals in time domain faced with the signals extracted from the multibody model. The FFTs of the simulated and the experimental signal contain the same frequency harmonics only with somewhat different power due to the real world light damping in the joints. The application of this approach may be extended to other cases i.e., the usefulness of mobile hydraulic cranes is limited because the payload is supported by an overhead cable under tension that allows oscillation to occur during crane motion. If the payload size is not negligible small when compared with the cable length may introduce an additional oscillatory mode that creates a multibody double pendulum. To give the insight into the double pendulum dynamics by Lagrangian methods two slender rods as payloads are analyzed dealing with the overhead crane and a composite revolute-revolute joint is proposed to model the cable of the hydraulic crane, both assumptions facilitates an affordable analysis. This allows developing a general study of this type of multibody payloads dynamics including its normal modes, modes ratios plus ranges of frequencies expected. Input Shapers were calculated for those multimodes of vibration by convolving Specified Insensitivity (SI) shapers for each mode plus a novel Direct SI-SI shaper well suited to reduce the computational requirements, i.e., the number of the shaper taps, to carry out the convolution sum in real time by the IoT device based on a single microcontroller working as the command generator. Several comparisons are presented for the shaped and unshaped responses using both the multibody model, the experimental FMI set-up and finally a real world hydraulic crane under slewing motion commanded by an analog Joystick connected by two RF modules 802.15.4 to the IoT device that carry out the convolution sum in real time. Input Shaping improves the performances for all the cases.

23 November 2023 in Journal of Vibration and Control
Verified
Journal Article
Closed access
Gerardo PelaezGerardo Pelaez
Gerardo Pelaez
CACristian Alonso
Cristian Alonso
HRHiginio Rubio
Higinio Rubio
JGJuan Carlos García-Prada
Juan Carlos García-Prada
Motion control for flexible link manipulators will have a great influence on their overall performance. Conventional control systems have the problem that they cannot compensate for the presence of uncertainty due to a variety of factors such as a change in the system itself-payload variations, degradation and modelling uncertainty. In addition, the underdamped structure of these systems entails motion-induced transient deflection and residual vibration. On the contrary, adaptive control, in particular Model Reference Adaptive Control (MRAC), has therefore been proposed to handle problems of this type dealing with other systems such as cranes, steering stability control for ground vehicles, airplanes and so on. This study presents a review and discussion on the MRAC and some individual issues of MRAC for these flexible link manipulators are addressed to specify: the state tracking error, the limitation of the adaptation values corresponding to the control gains and the control effort. Dealing with the last one, this work proves that shaping the command input to a Model Reference Adaptive Control (IS-MRAC) reduces the control effort necessary for the plant to follow the reference model and also mitigates the detrimental effects of flexibility. The IS-MRAC is implemented in a Single-Link Flexible Manipulator whose natural frequencies, experimentally and analytically estimated using the Transfer Matrix Method plus symbolic computation, vary significantly depending on payload mass and position. To this structured or parametric uncertainty, the proposed Lyapunov control law using the states associated with the low mode is designed for asymptotic stability and accommodates correctly. The state tracking, vibration suppression and control effort reduction performances of the proposed IS-MRAC combined controller are analysed via numerical simulations and experiments.

31 July 2025 in Actuators
Verified
Journal Article
Open access
PDF file
Gerardo PelaezGerardo Pelaez
Gerardo Pelaez
PIPablo Izquierdo
Pablo Izquierdo
GPGustavo Pelaez
Gustavo Pelaez
Higinio Rubio AlonsoHiginio Rubio Alonso
Higinio Rubio Alonso
The Furuta pendulum is a well-known benchmark in the field of underactuated mechanical systems due to its reduced number of control inputs compared to its degrees of freedom, and richly nonlinear behavior. This work addresses the challenge of accurately modeling and controlling such a system without relying on traditional linearization techniques. In contrast to the common approach based on Lagrangian analytical modeling and state–space linearization, we propose a methodology that integrates a high-fidelity multibody model developed in Simscape Multibody (MATLAB), capturing the complete nonlinear dynamics of the system. The multibody model includes all geometric, inertial, and joint parameters of the physical hardware and interfaces directly with Simulink, enabling realistic simulation and control integration. To validate the physical fidelity of the multibody model, we perform a frequency-domain analysis of the pendulum’s natural free response. The dominant vibration frequency extracted from the simulation is compared with the theoretical prediction, demonstrating accurate capture of the system’s inertial and dynamic properties. This validation strategy strengthens the reliability of the model as a digital twin. The classical analytical formulation is provided to validate the simulation model and serve as a comparative framework. This dual modeling strategy allows for benchmarking control strategies against a trustworthy nonlinear digital twin of the Furuta pendulum. Preliminary experimental results using a physical prototype validate the feasibility of the proposed approach and set the foundation for future work in advanced nonlinear control design using the multibody representation as a digital validation tool.


1 January 2007 in Shock and Vibration
Verified
Journal Article
Open access
PDF file
Gerardo PelaezGerardo Pelaez
Gerardo Pelaez
Jesus Doval-GandoyJesus Doval-Gandoy
Jesus Doval-Gandoy
NCN. Caparrini
N. Caparrini
JGJ.C. García-Prada
J.C. García-Prada
An investigation of the response of a physical pendulum to time delay filtered inputs was conducted. It was shown that the physical pendulum model is more accurate than the simple pendulum for modelling the dynamic response of overhead cranes with loads hanging from hooks. Based on the physical pendulum model a Specified Time Delay filter for an experimental mini overhead crane was synthesized. While somewhat limited in the scope by the hardware conditions placed in the system, the results provide basic insights into the successful application of the Time Delay Filtering method to overhead cranes.

1 July 2007
Verified
Conference Paper
Closed access
Gerardo PelaezGerardo Pelaez
Gerardo Pelaez
NCN. Caparrini
N. Caparrini
JGJ.C. Garcia-Prada
J.C. Garcia-Prada
This work addresses some new trends in the design of two impulse shaper for command generation for flexible mechanical couplings with variable stiffness. It is shown that this nonlinearity degrades the performances of traditional shapers. However a good choice for the modeled frequency of the filter can counteract the detrimental effect of the variable stiffness. This work solves the choice of the assumed frequency for the non-linear flexible link by extracting it from the phase plane and compares the impulses response with others options for the modeled frequency by estimate of the variable elasticity effect into the Time Delay Filters vector diagram.