The usability of homopolymer-based external calibration is investigated by ¹H-qNMR for PS, PVC, BR, PA and PET. Respective experiments are conducted in the context of copolymer quantification and the quantification of corresponding polymer mixtures.

Despite various developments in the application of quantitative nuclear magnetic resonance (qNMR) spectroscopy toward microplastics in recent years, this method still lacks suitable sample preparation and fractionation procedures.

Here, we report on the feasibility of using quantitative NMR and ultra-microbalances for additional measurements of the mass of poly-ethylene terephthalate (PET) particles in a reference material (RM). The microplastic (MP) PET particles were immobilised in solid NaCl following freeze-drying of a 1-ml NaCl suspension. The particles ranged from 30 to about 200 µm (Feret_min). In a 3-day process, more than 500 such units of PET particles in the NaCl carrier were prepared and later used in a large-scale inter-laboratory comparison. The homogeneity of PET in the salt carrier over these 500 units had previously been evaluated with respect to the mass of PET using an ultra-microbalance. In addition to the original results obtained by weighing, two independent results of quantitative ¹H-NMR have been obtained for further investigation of this reference material together with one additional set of weighing data. The NMR data were used for confirmation of the weighed amount of PET (as weighing is non-specific for PET). Average masses of 0.293 ± 0.04 mg and 0.286 ± 0.03 mg of PET were obtained using two different ultra-microbalances (14% RSD for n = 14 and 9% RSD for n = 4, respectively). The corresponding ¹H-NMR data was 0.300 ± 0.02 mg of PET (6.7% RSD for n = 5) and 0.345 ± 0.04 mg of PET (12.5% RSD for n = 14), respectively. The average mass of PET obtained by ¹H-NMR measurements was in agreement with the weighed amounts within their standard deviations. A mean value of 0.306 mg PET with an expanded uncertainty of 0.058 mg (± 19% relative) was calculated, and it is traceable to the SI system of measurements. Measurement of PET by quantitative ¹H-NMR spectroscopy is also reported for a water sample. The PET contained in one RM sample was transferred to 1 L of water to mimic a drinking water sample for microplastics. Graphical abstract

Tire wear particles (TWPs) are among the most relevant sources of microplastic pollution of the environment. Nevertheless, common analytical methods like IR and Raman spectroscopy are highly impaired by additives and filler materials, leaving only thermogravimetric methods for chemical analysis of TWPs in most cases. We herein present quantitative NMR spectroscopy (qNMR) as an alternative tool for the quantification of the polymeric material used for the production of tires, including natural rubber (NR), styrene–butadiene–copolymer (SBR), polyethylene–co-propylene (EPR) and polybutadiene (BR). Limits of quantification (LOQ) between 3 µg and 43 µg per sample and recovery rates of 72–92% were achieved for all tested polymer types. The first results of combining these measurements with Soxhlet extraction as a sample preparation tool are presented alongside the qNMR experiments.

With an increasing need in microplastic (MP) research there is also a persistent demand for further development of respective detecting and quantifying methods. To the current state, no technique is able to cover all different kinds of polymer types, instead valid characterisation is most likely to demand a combination of complementing approaches. In this regard, a promising technique introduced recently is quantitative nuclear magnetic resonance spectroscopy (qNMR), combining structural analysis of MP molecules with precise quantification. Despite various publications, however, qNMR is seldomly applied in environmental investigations. This study therefore, introduces an easy-to-apply preparation protocol for environmental qNMR analysis. It extends our recent efforts in MP fractioning by organic matrix removal, while at the same time transferring the method to more affordable benchtop devices. Finally, a semi-quantitative investigation of diffusion sequences is presented, enabling a more detailed analysis of MP mixtures in environmental samples.

Tire wear particles (TWP) are among the most relevant sources of microplastic pollution of the environment. Nevertheless, common analytical methods like IR- and Raman spectroscopy are highly impaired by additives and filler materials, leaving only thermo-gravimetric methods for chemical analysis of TWP in most cases. We herein present quantitative NMR spectroscopy (qNMR) as an alternative tool for the quantification of the polymeric material used for the production of tires including natural rubber (NR), styrene-butadiene-copolymer (SBR), polyethylene-polypropylene-copolymer (EPR) and polybutadiene (BR). Limits of quantification between 3 µg and 43 µg per sample and recovery rates of 72-92% are achieved for all tested polymer types. The first results of combining these measurements with Soxhlet extraction as a sample preparation tool are presented alongside the qNMR experiments.