Single-mode VCSEL technology has advanced significantly in the past few years. The advantages of single-mode VCSELs lie primarily on the narrower linewidth, lower numerical aperture and smaller spot size compared to multimode VCSELs. They are suitable for transmitting over both multimode fibers and few-mode fibers. For multimode fiber systems, the narrow linewidth can reduce the chromatic dispersion penalty and increase the system reach. A single-mode VCSEL also allows the coupling into graded-index single-mode fiber, which is few-mode around 850 nm with high bandwidth, for few-mode transmission. We review recent progress and present new experimental results and modeling analyses of single-mode VCSEL transmission over both types of fibers. The experiments and analyses shed new light on how single-mode VCSELs can be used with multimode fibers and graded-index single-mode fibers and relative merits between 850 nm single-mode VCSELs versus 980 nm and 1060 nm single-mode VCSELs to address the needs of various applications.
6 February 2019 in Journal of Lightwave Technology
The throughput of submarine transport cables is approaching fundamental limits imposed by amplifier noise and Kerr nonlinearity. Energy constraints in ultra-long submarine links exacerbate this problem, as the throughput per fiber is further limited by the electrical power available to the undersea optical amplifiers. Recent works have studied how employing more spatial dimensions can mitigate these limitations. In this paper, we address the fundamental question of how to optimally use each spatial dimension. Specifically, we discuss how to optimize the channel power allocation in order to maximize the information-theoretic capacity under an electrical power constraint. Our formulation accounts for amplifier physics, Kerr nonlinearity, and power feed constraints. Whereas recent works assume that the optical amplifiers operate in deep saturation, where power conversion efficiency (PCE) is high, we show that given a power constraint, operating in a less saturated regime, where PCE is lower, supports a wider bandwidth and a larger number of spatial dimensions, thereby maximizing capacity. This design strategy increases the capacity of submarine links by about 70% compared to the theoretical capacity of a recently proposed high-capacity system.
Power efficiency of long-haul optical fiber transmission has emerged as a critical challenge to cost-effectively increasing submarine cable capacity. Building on previous experimental work and informed by physical system modeling and optimization, we report on extensive amplified transmission experiments characterizing the metric of fiber capacity per unit pump power over a range of amplifier powers and link distances relevant to power-limited spatial-division-multiplexed submarine systems. We compare experimental results with modeling incorporating optical amplifier physics as well as generalized droop, demonstrating excellent agreement over the range of powers and distances tested. We predict the performance gains achievable by further optimizing the system design and implementation within tolerances ideally achieved in deployed submarine systems, and estimate fiber pair counts and total cable capacities achievable for the link distances investigated. Our results suggest the utility of amplifier pump powers as low as 20 mW and output powers as low as 6.5 dBm in reaching Pb/s cable capacities.
We propose a large core multimode fiber with 100-µm core diameter for short distance communication that is compatible with existing transceivers designed for 50-µm diameter core multimode fibers. The fiber exhibits a bandwidth that is over four times higher than the 50-µm OM4 fiber, low bending loss, and large connector offset tolerance. We have studied the bandwidth capability through both detailed modeling and experiments. A prototype fiber was fabricated, and it achieves 24 GHz km peak modal bandwidth in the 850 nm window, and the wavelength window with bandwidth above 5 GHz km is more than 100 nm. The bending losses of the fiber measured at 850 and 1300 nm with an encircled flux launch condition exceed the requirements for bending insensitive multimode fibers. The fiber has much higher connector offset tolerance compared to conventional 50-µm diameter core fibers as has been exhibited by modeling and experimental study. The additional loss caused by up to 10-µm connector offset is only 0.3 dB. Transmission experiments using 25 G SR and 100 G shortwave wavelength division multiplexing transceivers over such a fiber show error-free performance over 500 and 300 m, respectively. The proposed large core multimode fiber can address versatile needs in short distance communication including the bandwidth for high data rate transmission and a wide wavelength window for wavelength multiplexed transmission. The large connector tolerance and low bending loss can also enable low cost, compact connectivity solutions with passive alignment and ease of handling.
14 December 2018 in Journal of Lightwave Technology
Universal fiber is an optical fiber that supports both multimode and single-mode transmission. It is a multimode fiber with a mode field diameter of the fundamental mode roughly matching that of a standard single mode fiber. In today's short distance communications, both multimode fiber and single mode fiber are used. Universal fiber can accommodate the needs of single mode and multimode transmission so that end users can take advantage of the cost and performance benefits of each transmission type. In this paper, we present the design and properties of universal fiber, as well as its transmission performance for 100G systems. We also explore several application scenarios where the fiber can be utilized. In particular, we illustrate how the fiber can be used in 5G wireless fronthaul applications to meet the current needs while providing a path for future upgrades. Testing results and discussions of practical issues are also presented.
Chromatic dispersion is an important fiber attribute affecting transmission performance over optical fibers. Various chromatic dispersion measurement methods have been developed primarily for single-mode fibers. In the literature, measurement techniques were also developed to characterize few-mode fibers and multi-mode fibers. These methods are often subject to some limitations. In this paper, a simple and robust measurement method for chromatic dispersion measurement of single-mode fibers, polarization--maintaining fibers, and few-mode fibers is presented using a frequency domain instrument and a vector network analyzer. The method is applied to all three types of fibers through one measurement methodology uniformly. Using a vector network analyzer, the measurement instrument obtains the complex transfer function of fiber transmission. The inverse Fourier transform of the measured complex transfer function is used to determine the group delays for each mode of the fiber. Although the sampling is highly under-sampled for the whole fiber link, through proper treatment of the data, we can de-alias the signals and obtain accurate values of the group delays of each mode. By measuring the group delays over different wavelengths, the data can yield the chromatic dispersion of each mode over the wavelength window.