Dispersed reinforcement in cement mortars plays a key role in increasing their durability and strength. The fibres act as binding elements in the structure, preventing the development of microcracks that can weaken the material. Fibres increase mechanical strength, elasticity and resistance to tension and compression, which translates into better physical and mechanical parameters of the material compared to mortars without fibres. The aim of this study was to determine the physical and mechanical parameters of mortars with the addition of currently produced steel, glass and basalt fibres. The influence of the selected fibre type on the compressive and flexural strength, water absorption and capillary rise of mortars was investigated. The rheological properties of the mortars, i.e., consistency and volume density, were also investigated. Compressive and flexural strength was tested after 7, 28 and 56 days, while capillary rise and water absorption were tested after 28 days of curing. The frost resistance of the mortars was also determined. For the mortars tested, correlations were established between compressive strength and flexural strength, as well as between water absorption and capillary pull-up. A full statistical analysis was performed for two parameters, i.e., compressive strength and capillary pull-up. The introduction of basalt fibres into the mortars resulted in an increase in compressive strength by approximately 5% and in flexural strength by 48% after 56 days of curing. A lower mass increase of approximately 30% was also observed in relation to the reference series in the water absorption and capillary pull-up test for the series of mortars with glass fibres.
In Poland and the European Union countries, environmental awareness of a rational waste management policy is growing every year. The main problem in waste management has become the lack of areas to store waste. The correct solution seems to be the recovery or recycling of waste. Mortar is one material whose properties can be consciously modified with selected additives derived from waste. The use of waste in mortar is not only waste management, but also the modification of its properties. Today, recycled additives such as various types of glass are increasingly being used in mortar. In Europe, glass recycling reaches up to 85% of all glass packaging. A large proportion of new glass packaging is produced from recycled glass. In Poland, the situation is completely different. Only a small percentage of recycled glass is reused. A significant amount of cullet and waste glass is stored in landfills. This is a major ecological problem, which is why opportunities are being sought to manage as much glass waste material as possible. The aim of the planned laboratory tests was to manage waste coloured glass in building mortars made from Portland cement CEM II/B-V 42.5R and to determine the effect of glass flour and dust replacing cement and sand in varying proportions on the rheological characteristics and physical-mechanical parameters of the mortars. As a result of the tests carried out, the influence of the two-fraction waste material on the basic properties of cement mortars, i.e. setting time, bulk density, consistency, compressive and flexural strength, absorbability and capillary rise, was determined. Compressive and flexural strengths were tested after 7, 14, 28 and 56 days of curing. Half of the specimens made were matured under laboratory conditions and the other half under varying weather conditions. The microstructure of the mortars was examined after 28 days of maturation under a scanning electron microscope.
The circular economy is becoming an increasingly important part of development strategies in various sectors, as it responds to critical challenges related to environmental protection, the rational use of natural resources and sustainable development. The transition from a linear to a circular model requires changes on many levels, both technological and social. In the circular model, it is crucial to design products with a view to their longer use and easier recycling and reuse. The aim of the research was to determine the physical and mechanical parameters of mortars with the addition of recycled material. The effect of the additive on the compres-sive and flexural strength, water absorption and capillary suction of mortars was inves-tigated. The rheological properties of mortars, i.e. consistency, bulk density and setting time, were also studied. The internal structure of the samples was examined using an industrial computer tomograph Nikon XT H 225 ST and the microstructure of the mortars was analysed. Thermal conductivity coefficients for mortars were estimated. The analysis of the conducted tests shows that the addition of recycled material affects the rheological properties of mortars, causing an increase in the flow of fresh mortars, an extension of the setting time and a reduction in bulk density. The recycled material affects the parameters of the hardened mortar, resulting in a reduction in compressive and flexural strength. The biocomponent causes the cement matrix to seal, resulting in a reduction in weight gain in the water absorption and capillary rise tests.