Said Zul Amraini

Dr. Said Zul Amraini

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 May 2023 in Heca Journal of Applied Sciences
Verified
Journal Article
Open access
PDF file
Zuchra HelwaniZuchra Helwani
Zuchra Helwani
SASaid Zul Amraini
Said Zul Amraini
JAJecky Asmura
Jecky Asmura
TSThasya Nurfadillah Siregar
Thasya Nurfadillah Siregar
VTVanny Efia Triwahyuni
Vanny Efia Triwahyuni
AAAmmar Ali Abd
Ammar Ali Abd
This study aims to synthesize and determine the characterization of activated CaO/Biochar and identify the effect of the mass ratio of CaO/Biochar and KOH concentration on the activity of CaO/Biochar catalysts for the synthesis of CPO-based biodiesel. CaO was obtained from eggshell waste. Biochar is obtained from palm fronds through a torrefaction process. CaO/Biochar catalyst was synthesized by impregnation process using KOH solution. The biodiesel transesterification process using CaO/Biochar catalysts. XRD analysis results obtained CaO and Ca(OH)2 compounds in the catalyst, and the basicity value of the catalyst was >9.3. The best catalytic activity of the CaO/biochar catalyst was obtained at a mass ratio of 12:10 and a concentration of 20% KOH catalyst, with a biodiesel yield of 75.1%.

21 October 2023
Verified
Journal Article
Open access
PDF file
SASaid Zul Amraini
Said Zul Amraini
SSSunitha Sari
Sunitha Sari
DADavid Andrio
David Andrio
WFWaman Fatra
Waman Fatra
RSReno Susanto
Reno Susanto
Bioethanol (C2H5OH) is an organic chemical widely used as a solvent. It is also applied in producing germicides, beverages, antifreeze, fuel, and depressants as an intermediate in producing other chemical substances. Generally, bioethanol is generated from the fermentation of glucose (sugar) accompanied by a distillation process. This study aimed to optimize bioethanol production against variations in pre-treatment and solvent concentrations through enzyme hydrolysis and fermentation of oil palm empty fruit bunches. The pre-treatment is an important stage in the conversion process of lignocellulosic biomass, as it eliminates lignin, reduces the crystallinity of the cellulose, and increases the porosity of the substance, thereby facilitating the hydrolysis process and glucose fermentation. The process was carried out with different concentrations of acid, base, and organolsov solvents, after that, it was hydrolyzed using cellulase enzymes for 24 hours and fermented using Saccharomyces Cerevisiae yeast for 5 days. Furthermore, the bioethanol produced was separated through a rotary vacuum evaporator at 180 rpm and a temperature of 78 °C. The highest ethanol content produced was 7.8% with 4% NaOH and 90 minutes of pre-treatment residence time.

2 January 2025 in Leuser Journal of Environmental Studies
Verified
Journal Article
Open access
PDF file
AAAli Ahmudi
Ali Ahmudi
CHChairul Hudaya
Chairul Hudaya
IGIwa Garniwa
Iwa Garniwa
SASaid Zul Amraini
Said Zul Amraini
ASAgus Sugiyono
Agus Sugiyono
SYSyefiara Hania Yumnaristya
Syefiara Hania Yumnaristya
The development of renewable energy is a key priority for the Indonesian government and many other nations. Utilizing biomass as a co-firing fuel in coal-fired power plants (PLTUs) offers a viable pathway to meet renewable energy targets in the electricity sector. Co-firing technology involves substituting coal with biomass at specific ratios while maintaining the operational quality and efficiency of the power plants. Indonesia plans to implement a co-firing program in 114 PLTUs, with a combined capacity of 18.1 GW, requiring approximately 9 million tons of biomass annually. This study aims to develop a biomass supply chain model for co-firing, focusing on transportation cost optimization. Geographic Information Systems (GIS), Multi-Criteria Decision Analysis (MCDA), and Linear Programming are employed to map biomass potential from agricultural waste, identify optimal storage and factory locations, calculate the shortest distances to PLTUs, and design an efficient supply chain. Key biomass sources considered include agricultural waste from rice, corn, cassava, palm oil, coconut, sugarcane, and rubber. The study concentrates on co-firing in the Java and Sumatra regions, which house 14 and 12 PLTUs, respectively. Assuming a 5% biomass mix, the total annual bio-pellet demand is estimated at 3.34 million tons. By contrast, the annual production capacity of bio-pellets is calculated to be 143.58 million tons, indicating a surplus supply. Optimization results confirm that the available biomass supply can adequately meet the co-firing requirements for PLTUs in Java and Sumatra. The study also identifies optimal locations for storage facilities and bio-pellet factories near PLTU sites, enhancing supply chain efficiency. By integrating data on biomass potential, storage, factory, and PLTU locations, this research facilitates the design of an effective and efficient biomass supply chain, contributing to the broader goal of renewable energy development.

28 March 2024 in Jurnal Pengabdian kepada Masyarakat (Indonesian Journal of Community Engagement)
Verified
Journal Article
Open access
PDF file
SASaid Zul Amraini
Said Zul Amraini
Implementation of Fish Pellet Production Using Palm Kernel Waste in Merangin Village, Kampar

2 January 2025 in Leuser Journal of Environmental Studies
Verified
Journal Article
Open access
PDF file
MMMuhammad Mardhiansyah
Muhammad Mardhiansyah
NSNur Suhada
Nur Suhada
ESEvi Sribudiani
Evi Sribudiani
SASaid Zul Amraini
Said Zul Amraini
HFHafid Farhan
Hafid Farhan
Management actions through rehabilitation activities can restore mangrove ecosystems by involving community participation. This study aims to determine the involvement and effectiveness of community-based rehabilitation activities. This study was conducted in Teluk Pambang Village, Bengkalis Regency. The method used is qualitative, with a purposive sampling technique based on certain criteria. The data analysis used is qualitative descriptive and data processing using nvivo 12 plus software. The research findings explain that the dominant factors that encourage people to carry out mangrove rehabilitation activities are based on additional income, strengthening the issue of carbon trade economy, kinship elements, and easy access to financing through donors. The level of program understanding, target accuracy, activity management, and real changes are the most effective rehabilitation activities for the community. At the same time, the indicators for achieving goals are still considered ineffective.

8 August 2023 in Leuser Journal of Environmental Studies
Verified
Journal Article
Open access
PDF file
WFWarman Fatra
Warman Fatra
KAKaspul Anuar
Kaspul Anuar
FOFebri Dwi Oktriyono
Febri Dwi Oktriyono
RFRivo Fernando
Rivo Fernando
Zuchra HelwaniZuchra Helwani
Zuchra Helwani
SASaid Zul Amraini
Said Zul Amraini
Fiberglass is the most common reinforcing fiber used in composites, with polymer matrices having high tensile strength and chemical resistance, including an excellent insulating property; however, they are non-degradable. Natural fiber reinforced polymer composites have advantageous properties such as lower density and price, when compared to synthetic composite products. In addition, hybrid composites may be obtained depending on various properties such as the fibers' length, structure, content and orientation, matrix bonding and arrangement. This study was carried out to determine the effect of adding Maleated Natural Rubber (MNR) from natural rubber as a coupling agent, in order to produce the highest tensile and flexural strength. The hand lay-up and vacuum bag methods with the Response Surface Method-Central Composite Design (RSM). -CCD) were used. The composite arrangement pattern was E-glass/OPEFB/E-glass, the volume fraction of OPEFB (oil palm empty fruit bunches):E-glass was 40:60, 50:50 and 60:40, the fraction volume of OPEFB + E-glass:matrix was 40:60, 50: 50, 60: 40 and the coupling agent were added by 9, 10 and 11% of the total epoxy resin used. Furthermore, the composite mold was made of glass with dimensions of 200mm x 50mm x 50mm. The results showed that the composite product obtained from both methods had a tensile strength value, which was influenced by the variable OPEFB fiber and epoxy resin. Meanwhile, the flexural strength was influenced by the OPEFB fiber and the quadratic factor of the epoxy-MNR resin.