Rudolf Weber

Prof. Dr. Rudolf Weber


Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 May 2014 in Optics Express
Verified
Journal Article
Closed access
PDF file
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf
PBPeter Berger
Peter Berger
VOVolkher Onuseit
Volkher Onuseit
MWMargit Wiedenmann
Margit Wiedenmann
AFAnne Feuer
Anne Feuer
Laser materials processing with ultra-short pulses allows very precise and high quality results with a minimum extent of the thermally affected zone. However, with increasing average laser power and repetition rates the so-called heat accumulation effect becomes a considerable issue. The following discussion presents a comprehensive analytical treatment of multi-pulse processing and reveals the basic mechanisms of heat accumulation and its consequence for the resulting processing quality. The theoretical findings can explain the experimental results achieved when drilling microholes in CrNi-steel and for cutting of CFRP. As a consequence of the presented considerations, an estimate for the maximum applicable average power for ultra-shorts pulsed laser materials processing for a given pulse repetition rate is derived.

1 December 2018 in Materials & Design
Verified
Journal Article
Open access
CHChristian Hagenlocher
Christian Hagenlocher
MSMartin Sommer
Martin Sommer
FFFlorian Fetzer
Florian Fetzer
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf

14 February 2017 in Optics Express
Verified
Journal Article
Open access
PDF file
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf
CFChristian Freitag
Christian Freitag
AFAnne Feuer
Anne Feuer
TKTaras Kononenko
Taras Kononenko
VKVitaly I. Konov
Vitaly I. Konov
In any pulsed and repetitive laser process a part of the absorbed laser energy is thermalized and stays in the material as residual heat. This residual heat is accumulating from pulse to pulse, continuously increasing the temperature, if the time between two pulses does not allow the material to sufficiently cool down. Controlling this so-called heat accumulation is one of the major challenges for materials processing with high average power pulsed lasers and repetitive processing. Heat accumulation caused by subsequent pulses (HAP) on the same spot and heat accumulation caused by subsequent scans (HAS) over the same spot can significantly reduce process quality, e.g., when the temperature increase caused by heat accumulation exceeds the melting temperature. In both cases, HAS and HAP, it is of particular interest to know the limiting number of pulses or scans after which the heat accumulation temperature exceeds a critical temperature and a pause has to be introduced. Approximation formulas for the case, where the duration of the heat input is short compared to the time between two subsequent heat inputs are derived in this paper, providing analytical scaling laws for the heat accumulation as a function of the processing parameters. The validity of these approximations is confirmed for HAP with an example of surface ablation of CrNi-steel and for HAS with multi-scan cutting of carbon fiber reinforced plastics (CFRP), both with a picosecond laser at an average power of up to 1.1 kW. It is shown that for the important case of 1-dimensional heat flow the limiting number of heat inputs decreases with the inverse of the square of the average laser power.

1 August 2019 in Optics and Lasers in Engineering
Verified
Journal Article
Closed access
MBMeiko Boley
Meiko Boley
FFFlorian Fetzer
Florian Fetzer
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf

1 May 2019 in Science and Technology of Welding and Joining
Verified
Journal Article
Open access
CHChristian Hagenlocher
Christian Hagenlocher
DWDaniel Weller
Daniel Weller
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf
The grain structure of laser welded AlMgSi-alloys was varied by adapting the welding parameters and alloying additives. The hot cracking susceptibility was determined by the critical strain rate, measured by the application of digital image correlation in a self-restrained hot cracking test. A direct relation was found: The hot cracking susceptibility decreases with increasing number of grain boundaries across the width of the weld seam, i.e. along the effective load direction of transverse strain rates. It was shown, that the hot cracking susceptibility can be reduced by an optimisation of both the welding parameters and the alloying additives, which promote nucleation.

3 July 2018 in Metals
Verified
Journal Article
Open access
PDF file
MJMichael Jarwitz
Michael Jarwitz
FFFlorian Fetzer
Florian Fetzer
RWRudolf Weber
Rudolf Weber
TGThomas Graf
Thomas Graf
Spatial beam oscillation during laser beam welding of aluminum to copper was investigated. The beam was spatially oscillated perpendicular to the direction of feed in a sinusoidal mode. The influence of the oscillation amplitude and frequency on the weld seam geometry and the implications on the electrical resistance of the joints was investigated. It was found that spatial beam oscillation allows to set the welding depth and seam width virtually independent of each other. Furthermore, low welding depths into the lower copper sheet in combination with high ratios of seam width at the interface of the two sheets to welding depth into the lower copper sheet result in low electrical resistances of the welds. Low electrical resistances were found to correlate with high mechanical strengths of the welds.