Mohsin Rafique

Dr. Mohsin Rafique


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2019 in Vacuum
Verified
Journal Article
Closed access
IAImran Asjad
Imran Asjad
RAR. Ahmad
R. Ahmad
NANaveed Afzal
Naveed Afzal
MRMohsin Rafique
Mohsin Rafique

1 February 2016 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
Verified
Journal Article
Closed access
MRMohsin Rafique
Mohsin Rafique
SCSan Chae
San Chae
YKYong-Soo Kim
Yong-Soo Kim

1 April 2012 in Radiation Effects and Defects in Solids
Verified
Journal Article
Closed access
MRMohsin Rafique
Mohsin Rafique
NANaveed Afzal
Naveed Afzal
RAR. Ahmad
R. Ahmad
SASajjad Ahmad
Sajjad Ahmad
IGI. M. Ghauri
I. M. Ghauri
Samples of polycrystalline zirconium were irradiated with fast neutrons (E>0.1 MeV) in Pakistan Research Reactor-1 at 423 K to fluences 1.22×1020, 4.87×1020 and 9.70×1020 n/m2. Mechanical properties such as yield stress (YS), ultimate tensile stress (UTS), percentage elongation, stress relaxation rate and hardness of the samples were measured before and after irradiation to analyze post-irradiation effects. The results indicate that neutron irradiation of polycrystalline zirconium does not produce any significant change in its mechanical properties. The YS, UTS and hardness slightly decrease, whereas the percentage elongation increases with an increase in the radiation fluence. Stress relaxation rate was found to be unaffected after irradiation. The post-irradiation microstructure of zirconium reveals that the surface of the material becomes rough by increasing the radiation fluence. X-ray diffraction analysis of the specimens indicates a decrease in the intensity of Bragg's reflection with an increase in the radiation fluence. The insignificant changes in the mechanical properties of zirconium after irradiation are attributed to low defects production in irradiated zirconium and subsequently their recombination due to irradiation temperature.

1 August 2019 in Ceramics International
Verified
Journal Article
Closed access
RYRabia Younas
Rabia Younas
NANaveed Afzal
Naveed Afzal
MRMohsin Rafique
Mohsin Rafique
IAImran Asjad
Imran Asjad
MSMurtaza Saleem
Murtaza Saleem
RAR. Ahmad
R. Ahmad

1 December 2018 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
Verified
Journal Article
Closed access
NANaveed Afzal
Naveed Afzal
MRMohsin Rafique
Mohsin Rafique
WJWajeeha Javaid
Wajeeha Javaid
RAR. Ahmad
R. Ahmad
AFAmeeq Farooq
Ameeq Farooq
ZKZubair Khaliq
Zubair Khaliq

1 September 2017 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
MRMohsin Rafique
Mohsin Rafique
MBM Z Butt
M Z Butt
SASajjad Ahmad
Sajjad Ahmad
Zircaloy-4 specimens were irradiated with 3.5 MeV hydrogen ions (dose range: 1 × 1013 H+1 cm−2 to 1 × 1015 H+1 cm−2) using a Pelletron accelerator. FESEM studies reveal formation of hydrogen micro-bubbles, bubbles induced blisters of irregular shapes, and development of cracks on the specimen surface, as in the case of pure zirconium. However, for the highest irradiation dose of 1 × 1015 H+1 cm−2, agglomeration of flower-shape blisters is observed. XRD analysis shows that the most preferentially oriented crystallographic plane is (0 0 4) with texture coefficient values 1.832–2.308 depending on the ions dose. Its diffraction peak intensity first decreases with the increase in ions dose up to 5 × 1013 H+1 cm−2 and later increases up to 1 × 1015 H+1 cm−2. Opposite is found in case of diffraction peak width. Crystallite size and lattice strain determined by Williamson–Hall analysis display a linear relationship between the two with positive slope. Mechanical strength, namely yield stress (YS), ultimate tensile strength (UTS), and fracture stress (FS), increases sharply with ions dose up to 5 × 1013 H+1 cm−2. For 1 × 1014 H+1 cm−2 dose there is a sudden drop of stress to a lowest value and then a slow steady increase in stress up to the highest dose 1 × 1015 H+1 cm−2. Same pattern is followed by uniform elongation and total elongation. All three stress parameters YS, UTS, and FS follow Inverse Hall–Petch relation.