Epoxy resin has been used to cast the core of the dry‐type high voltage direct current bushings and can accumulate space charge under high electric fields at high temperatures, which is believed to be a potential threat to the safe operation of dry bushings, especially under polarity reversal. In this study, results of a study of the evolution of space charge and electric field distribution in epoxy resin, under polarity reversal at 10 and 20 kV/mm, and at temperatures between 40 and 100°C, are presented. The results show that the space charge dynamics in epoxy resin during the test were different at various temperatures. At temperatures no more than 60°C, space charge accumulation within the samples was not obvious. Instead, a low‐frequency dielectric relaxation process maybe occurs during the polarity reversal, which made the charge peaks on the electrodes after the reversal were slightly smaller than those before the reversal. At temperatures no less than 80°C, considering that the applied electric field has little effect on the barrier reductions of the traps within the samples, the space charge dynamics were mainly governed by a thermally activated process, and the depths of the deepest occupied traps were obtain by analysing the transient processes.
1 May 2019 in IET Science, Measurement & Technology
Graphene has attracted much attention due to its advanced properties. In previous work, the relationship between temperature and the conductivity of epoxy‐based nanocomposite filled with graphene oxide has been experimentally studied. To understand the charge transport behaviour, the space charge characteristics at different temperatures and field strengths are measured with an improved pulsed electroacoustic measurement system, which is designed for high‐temperature space charge measurement. From the measurement results, epoxy resin (ER) filled with multi‐layer graphene oxide (MGO/ER) shows suppressed charge migration while ER filled with single‐layer graphene oxide (SGO/ER) shows a hetero charge accumulation, which is assumed to be caused by the partial reduction of graphene oxide to graphene. Compared to pure ER, the apparent mobility of the nanocomposites is smaller while the trap depth and number of trapped charges are larger, which is probably caused by the introduction of traps. In the simulation, the relationship between mobility, trap depth, trap density and charge distribution are firstly studied. Then the calculated values of mobility and trap depth are given to the parameters to compare the simulated charge profiles with experiment results. The simulation results agree well qualitatively with the experimental results, giving some support for the proposed explanations.
1 December 2021 in Journal of Materials in Civil Engineering
Microwave-assisted concrete liberation and aggregate recycling is highlighted by many research groups due to its efficient and effective recycling process. In this paper, a series of experiments are conducted to study the heating results of concrete under microwave and conventional heating processes. The temperature variations of concrete under two different heating approaches are obtained. The crack characteristic and material damage during the different heating processes are illustrated. Particularly, the energy efficiency was investigated for two approaches. Results proved that concretes were broken more effectively under microwave irradiation than in conventional furnaces, and the aggregates can be easily separated under the sufficient power input. Scanning electron microscope (SEM) analysis proved that after microwave treatment, intergranular fractures are formed at mortar-aggregate interfaces, few cracks occurred after conventional heating processes. The research proves that, compared with conventional heating, microwave irradiation could liberate concrete and recycle aggregate effectively, with less heating duration and lower energy input required.
As the main insulating material of an ultra-high voltage (UHV) resin impregnated paper (RIP) bushing, epoxy resin accumulates space charge under the DC voltage, which would affect the insulation properties of the bushing. In this article, the evolution of space charge accumulation and dissipation within the epoxy resin samples was measured under the influence of a long-term (24 h) electric field of 60 kV/mm at 40°, 60°, 80°, and 100°C. The experimental results show that the space charge transport in the epoxy sample was a long-time dynamic process. When the temperature was not greater than 60°C, only homocharge accumulation was observed within the samples, and the space charge distribution did not reach a stable state even after 24 h of voltage application. When the temperature was not lower than 80°C, the positive heterocharge accumulation was observed at the interface between cathode and epoxy. Through analysis by fitting and numerical simulation, it was verified that the positive heterocharge accumulation was caused by the limitation of the hole extraction, and the transport of holes within the samples obeyed the jump conductance model.
25 October 2024 in Journal of Physics D: Applied Physics
Epoxy resin serves as a critical insulating component in ultra-high voltage dry direct current bushings. However, the accumulation of space charges within the epoxy resin, a byproduct of charge mobility, poses a significant risk to the reliability and operational safety of bushings. Conventional space charge attenuation models, especially after voltage removal, have limited use in simulations aimed at understanding this phenomenon. This study introduces an improved model integrating the bipolar charge transport mechanism with space charge decay based on the hopping conduction mechanism and Schottky’s theorem, establishes a theoretical framework for predicting the space charge behavior following voltage removal, and conducts a simulation to investigate the decay process within the internal structure of epoxy resin and measure the residual charges after voltage removal using the pulsed electro-acoustic method. The experimental data validate the accuracy of the proposed model and theoretical assumptions. The findings show that the remaining negative charges after voltage removal are not enhanced by the field enhancement; the anodic positive and cathodic positive charges are distributed in two-segment discontinuous traps, whereas the negative charges are distributed in one-segment traps. The model identifies two distinct trapping sites for anodic and cathodic positive charges, and one trapping site for negative charges. After voltage removal, when the field strength exceeded 40 kV mm−1, positive charges exist near the upper and lower electrodes, and negative charges exist near the center of the specimen. The consistency between the simulated predictions and experimental data proves the effectiveness of the proposed model in accurately simulating the space charge decay in epoxy materials after voltage removal.
Epoxy resin impregnated crepe paper (ERICP) composites is the main insulating material of the ultra-high voltage direct current (UHVDC) dry bushing. The moisture in the environment may intrude into the ERICP composites in the manufacturing process of the bushing, which would affect the quality of the bushing. In order to investigate the diffusion process of moisture in the ERICP composites during the manufacturing process, the ERICP samples were casted under a vacuum according to a certain formula. Five different artificial humidity environments were produced in sealed containers by different saturated salt solutions. The weights of ERICP samples under different humidity were periodically measured so as to determine the moisture absorption behaviors of the samples. The moisture diffusion behaviors in the samples showed that the one dimensional Fickian law can't exactly describe the moisture diffusions in ERICP samples at long time, especially under high relative humidity. The dielectric spectra of ERICP samples within saturated absorbed moisture were then measured at room temperature, which frequency changed from 10-3 Hz to 106 Hz. The low frequency dispersion (LFD) process and the mid-frequency dispersion process appeared in dielectric spectra of ERICP within moisture absorption. The absorbed moisture shifted the spectra to the up and right, which moved to higher frequencies. The LFD means that some clusters were formed in ERICP samples after absorbing moisture. The moisture absorbed by the epoxy resins of ERICP may exist only in `mobile' phase, while the moisture in the crepe paper impregnated with epoxy resins may exist in both `mobile' phase and `bound' phase.