Examining dual vertical-axis wind turbines (VAWTs) across various turbulence scenarios is crucial for advancing the efficiency of urban energy generation and promoting sustainable development. This study introduces a novel approach by employing two-dimensional numerical analysis through computational fluid dynamics (CFD) software to investigate the performance of VAWTs under varying turbulence intensity conditions, a topic that has been relatively unexplored in existing research. The analysis focuses on the self-starting capabilities and the effective utilization of wind energy, which are key factors in urban wind turbine deployment. The results reveal that while the impact of increased turbulence intensity on the self-starting performance of VAWTs is modest, there is a significant improvement in wind energy utilization within a specific turbulence range, leading to an average power increase of 1.41%. This phenomenon is attributed to the more complex flow field induced by heightened turbulence intensity, which delays the onset of dynamic stall through non-uniform aerodynamic excitation of the blade boundary layer. Additionally, the inherent interaction among VAWTs contributes to enhanced turbine output power. However, this study also highlights the trade-off between increased power and the potential for significant fatigue issues in the turbine rotor. These findings provide new insights into the optimal deployment of VAWTs in urban environments, offering practical recommendations for maximizing energy efficiency while mitigating fatigue-related risks.
This study analyzes the performance degradation of traditional hybrid wind turbines under high blade-tip-speed ratio conditions and proposes solutions through two-dimensional Computational Fluid Dynamics (CFD) simulations. It also introduces the design of two innovative asynchronous-hybrid dual-rotor wind turbines. The results indicate a remarkable 98.5% enhancement in torque performance at low blade-tip-speed ratios with the hybrid wind turbine model. However, as the blade-tip-speed ratio increases, it leads to negative torque generation within the inner rotor of the conventional design, resulting in a reduction of the power coefficient by up to 13.1%. The introduction of the new wind turbine design addresses this challenge by eliminating negative torque at high blade-tip-speed ratios through adjustments in the inner rotor’s operating range. This modification not only rectifies the negative torque issue but also enhances the performance of the outer rotor in the leeward region, consequently boosting the overall power coefficient. Moreover, the optimized inner rotor configuration effectively disrupts and shortens the wake length by 16.7%, with this effect intensifying as the rotational speed increases. This optimization is pivotal for enhancing the efficiency of multi-machine operations within wind farms.
The double vertical-axis wind turbine (VAWT) system serves as a high-performance design solution. The Nautilus wind turbine investigated in this research imitated the structure of a Nautilus shell and is a vertical-axis drag-type wind turbine that exhibits relatively low efficiency. Therefore, the improvement of its wind energy efficiency is of paramount importance. This paper utilizes Computational Fluid Dynamics (CFD) software, based on the Reynolds-averaged Navier–Stokes equations and dynamic meshing techniques, to conduct numerical investigations on the aerodynamic performance of the Nautilus wind turbine array layout. The effects of wind direction, spacing ratio, and rotation direction are individually studied, and the interpretations and explanations are provided based on flow field characteristics. The results show that when the wind direction is 90°, i.e., a transverse layout, the closer the spacing between the transverse turbines, the higher the average power coefficient of the entire wind turbine system, with little effect from the three rotation directions. The maximum average power coefficient reached 28.9% and the power gain factor (TPGF) reached 11.1%. The enhancement effect primarily originates from the wake interaction among neighboring turbines. The experimental results showed a deviation of 8.1% compared to the CFD simulation results, thus validating the accuracy of the numerical CFD modeling. Ultimately, several array layouts are proposed, based on the prevalent wind direction and spacing ratio research. The enhancement of the wind turbine array’s situation could significantly increase the average efficiency of the entire wind turbine cluster. Consequently, this study provides a reference for the practical application of biomimetic vertical-axis drag-type wind turbine systems in actual engineering.
With the growing utilization of disc motors, the enhancement of their operational stability has become a critical research area. The existing studies usually focus on improving the pole structure of the rotor or the stator structure to optimize one performance of the motor and less on optimizing multiple performances. This paper simultaneously improves the rotor pole structure and stator tooth structure of the motor in order to optimize the sinusoidal waveform of the no-load back electromotive force and the cogging torque at the same time to achieve the goal of reducing the vibration and noise of the permanent-magnet synchronous dual-rotor statorless magnetically coupled disc motor and improve its operational stability. A finite element simulation model of a 20-pole, 24-slot permanent-magnet synchronous dual-rotor statorless magnetically coupled disc motor is established to analyze the influence of various factors, including the number of magnetic pole steps, the opening position, depth, and width of the stator auxiliary slot, on the motor performance. The results show that this stator–rotor combination improvement method effectively reduces the total harmonic distortion (THD) and attenuates multiple harmonics, and the peak cogging torque pulsation is significantly improved while other properties of the motor meet the technical requirements, and the motor performance is improved.
An enhanced chaotic particle swarm optimization fuzzy PID is introduced to address the hydraulic wind turbine grid-connected speed control conditions. In the enhanced algorithm, a Circle chaotic mapping is combined with particle swarm optimization (PSO) to prevent PSO from becoming trapped in local optima. Moreover, a linear inertia weight reduction strategy is integrated to harmonize the algorithm’s capacity for expansive exploration and meticulous exploitation. Then, the enhanced algorithm is utilized to adjust and perfect the configuration variables within the fuzzy PID system. Based on the optimization, speed characteristics of the variable motor are analyzed. Simulation results show that when the swash plate angle factor varies within a specific range, the variable motor speed is only related to the quantitative pump speed. When the input speed of the quantitative pump changes in a step from 400 to 500 r/min, the enhanced CPSO fuzzy PID control approach reduces ascension time by 40% and 76%, and settling time by 80% and 76%, compared to the fuzzy PID and PSO fuzzy PID control approaches, respectively. When the input speed changes in a step from 500 to 600 r/min, the approach reduces ascension time by 25% and 72%, and settling time by 80% and 72%, respectively. When the input speed varies within a range of 400–500 r/min, the approach reduces ascension time by 37.5% and 80%, and settling time by 83% and 80%, respectively. And the enhanced CPSO fuzzy PID speed-control system exhibits no overshoot. Therefore, the enhanced CPSO fuzzy PID algorithm enhances the quantitative pump-motor system’s stability and rapidity, meeting hydraulic wind turbine grid-connected speed-control needs.