To study the influence of consolidation stress ratio and stress history on 1-D consolidation permeability of saturated clay, one-dimensional consolidation permeability tests were carried out with GDS triaxial device. The results indicated that the permeability coefficient and void ratio of normally and overconsolidated saturated clay decreased with the increase of consolidation stress ratio under different consolidation stress ratios but the same stress history. And the amount of final sample’s compression increased with the increase of the consolidation stress ratio. Under the condition of the same consolidation stress ratio but different stress history, the amount of final compression of the overconsolidated saturated clay was smaller than that of the normally consolidated saturated clay. Besides, the stress difference σdv between consolidation pressure and gravity stress was fitted to the amount of the final sample’s compression, and a good linear relationship between the stress difference and the amount of the final sample’s compression under each consolidation pressure was obtained. The results showed that it is necessary to consider the influence of consolidation stress ratio and stress history simultaneously on 1-D consolidation permeability of saturated clay. Meanwhile, it can accurately predict the amount of the final sample’s compression after knowing the gravity stress. Moreover, a model prediction analysis was conducted on the saturated clay and recommended to use the modified Kozeny-Carman’s equation to predict the permeability coefficient of Luochuan saturated clay during one-dimensional consolidation.
For a retaining wall adjacent to rock or rigid structures, existing model test results indicate that the slip soil in the limit state can be approximated as a trapezoidal slip wedge. Based on the static equilibrium condition of the slip wedge, a calculation method for active and passive earth pressures is proposed that considers the effect of backfill width through extreme value analysis. As the backfill width increases, the trapezoidal slip wedge transitions to a triangular slip wedge, introducing a critical width to distinguish between finite and semi-infinite soil conditions. For cohesionless soils, the proposed method converges to Coulomb theory at the critical width; when the backfill is clay, the critical width exceeds the width of Coulomb’s triangular slip wedge due to the stabilizing contribution of cohesion. Parameter analysis reveals that with increasing backfill width, the active earth pressure of cohesionless soil follows a non-linear upward trend, whereas the passive earth pressure decays exponentially. For clay, the active earth pressure initially increases with backfill width and then decreases, whereas the passive earth pressure first decays exponentially and then exhibits a slight increase. Variations in the friction angle significantly affect both active and passive earth pressures, while cohesion mainly influences active earth pressure, and wall-soil friction angle exerts a stronger impact on passive earth pressure. The effectiveness of the proposed method is verified by comparison with results from model tests and numerical simulations.
The pumped storage power station (PSPS) is an important measure to achieve the strategic goal of “dual carbon”. As one of the preferred types for the upper reservoir dams of PSPSs, the concrete-faced rockfill dam (CFRD) often has a dam foundation on a steep transverse slop and is prone to produce slip deformation along the slope, resulting in poor anti-sliding stability of the dam slope. It is dangerous for the operation safety of PSPSs. Therefore, the slip deformation of CFRDs on dam foundations with large dip angles is investigated. The mechanism for the initiation of slip deformation is revealed. The design measures of physical mechanic and geometric structure are proposed to reduce slip deformation. The results show that the larger sliding forces and smaller anti-sliding forces are the fundamental reasons that CFRDs on dam foundations with large dip angles are prone to produce slip deformation. The larger the dip angle of the dam foundation, the larger the slip deformation of the dam body and face slab, and the smaller the safety factor of the dam slope. When the dip angle of the dam foundation is greater than 15°, the safety factor of the dam slope is less than the minimum value of 1.5 required by codes. The addition of pressure slopes can effectively reduce the slip deformation of the dam body or face slab and significantly improve the anti-sliding stability of the dam slope. When the height or width of the pressure slope platform is greater and the cohesion or internal friction angle of the pressure slope is larger, the slip deformations of the dam body and face slab are smaller, and the safety factor of the dam slope is greater. It is recommended that the height and width of the pressure slope platform be 1/2 times the maximum height of the main dam, and the density (cohesion and internal friction angle) of the pressure slope be equivalent to that of the main dam’s rockfill material. The research results can provide theoretical and technical support for the design and construction of CFRDs for the upper reservoir of PSPSs.
The current formula of critical hydraulic gradient is not adapted to solve critical hydraulic gradient of cohesive soil. Assume that the seepage failure mode of the cohesive soil foundation was cylindrical or inverted circular truncated cone, based on the calculation formula of the critical hydraulic gradient of Terzaghi, the analytical formula of the critical hydraulic gradient considering the influence of the shear strength of the soil was derived. Then, the seepage failure process of the clay layer was simulated numerically, and the effects of the clay layer thickness, failure radius, and shear strength indexes on the critical hydraulic slope were analyzed. The comparison results show that the numerical test results are in good agreement with the calculated results of the new formula. In addition, the critical hydraulic gradient of sandy loam and loess under different working conditions was studied severally by a self-made permeation failure instrument. The results show that the critical hydraulic gradient decreases with the increase of soil thickness and failure radius, and the maximum error between the test and the corresponding formula results is no more than 16.
In the process of piping development, the sediment carried by seepage causes the change of porosity and then causes the change of permeability coefficient. Therefore, piping belongs to muddy water seepage (i.e., unstable seepage). Based on the theory of muddy water seepage, the new control equation of piping model is established. The generation mechanism and development process of piping for white fine sand and sand gravel are explored. The advantages for the new control equation of piping model are discussed. The results show that the new control equation of piping model is not only simpler in form but also easier to solve and can better describe the characteristics of piping generation, development, and stability. Compared with white fine sand (the initial relative density and porosity are smaller, and the initial permeability coefficient and critical gradient are larger), the porosity, permeability coefficient, seepage flow, and sediment volume of sandy gravel increase faster with time. When the porosity is the same, the permeability coefficient, seepage flow, and sediment volume of sand gravel are larger. The smaller the area affected by piping, the faster the increase of porosity, permeability coefficient, seepage flow, and sediment volume. When the porosity and permeability coefficient are the same, the seepage flow and sediment volume are smaller. The smaller the initial porosity and permeability coefficient, the later the generation, and development of piping. It can provide a reference for piping danger forecast and emergency response.