Extreme climate change is today’s world’s most pressing and challenging problem. Increases in greenhouse gas emissions, the warming of the atmosphere and ocean, increased precipitation, rising sea levels, and temperature rise are the major effects of climate change that significantly affect urban infrastructure. Green Infrastructure (GI) is an increasingly acknowledged tool for climate change adaptation that contributes to sustainable urban and rural development. This study reviewed 111 research articles to identify and summarize the research findings about the role of GI in climate change adaptation. Furthermore, the research articles are grouped into three sectors with the most benefits of green infrastructure in climate change adaptation: mitigating urban heat islands, increasing ecosystem resilience, and flood risk management. The literature was further divided according to the developed or utilized strategies and techniques. The findings suggest that the topic of GI’s role in climate change adaptation is very current and it has been studied frequently in the last five years.
1 September 2022 in Journal of Transportation Engineering, Part A: Systems
Three safety concerns have been identified in the conventional design consistency assessment procedure for horizontal curves: approximation of the vehicle by the point-mass model, use of unrealistic speeds, and the assumption that the path radius is equal to the design curve radius. This study presents a novel approach to the consistency assessment of horizontal curves in terms of vehicle stability (represented as the safety margin). The novel approach involves calculating the safety margins using the steady-state bicycle model to account for the nonuniform distribution of friction among individual axles due to grade and speed changes and using more-realistic driver behavior parameters. In this study, the realistic driver behavior parameters refer to the modeled operating speeds and calculated vehicle path radii, which were defined based on naturalistic driving data collected through a real-world experiment on a section of a two-lane state road using a GPS device. The analysis showed that the traditional safety margins for sharp curves are unrealistically large compared with the margins defined by the proposed approach; this indicates that the conventional approach uses a larger friction margin than the optimum friction margin. Consequently, the conventional approach results in the application of curves with radii smaller than those required for safe driving. Moreover, the results show that braking on a sharp curve on a steep downgrade is the most critical situation for the loss of lateral vehicle stability. Overall, this study highlights the significance of incorporating additional factors in the design procedure for horizontal curves that affect the safety of the curve, which are not considered in the point-mass model. The most significant factors considered in this study were the grade, driving maneuver in terms of speed change, operating speed, and vehicle path radius. The primary objective of this research was to establish a reliable road design methodology for reducing single-vehicle accidents on horizontal curves. The proposed approach enables the identification of horizontal curves with insufficient side friction, by calculating the difference between the available side friction factor and side friction demand. In a conventional road design practice, the vehicle is approximated as a point mass, and the effects of grade, speed change, vehicle dimensions, and uneven force distribution on individual axles are ignored. Instead, in the novel approach, the steady-state bicycle model was used, considering the aforementioned factors combined with more-realistic speeds and path radii. The improved approach provides a more comprehensive understanding of the design of safe curves, with an emphasis on previously neglected important influential factors (longitudinal grade and driver behavior in terms of operating speed and path radius). The improved design consistency approach could be used for quantifying the risk of skidding, both in the design stage of new roads and for improvement of existing roads.
27 June 2016 in The Baltic Journal of Road and Bridge Engineering
Experimental investigation was conducted on a 24 km long segment of the two-lane state road to collect the driver behavior data. The research involved 20 drivers driving their own cars equipped with the GPS device. Considering the impact of path radius and speed on the side friction demand, the design consistency on horizontal curves was evaluated by determining the margins of safety. The analysis showed that the vehicle path radii were mainly smaller than curve radius, on average for 12%. Regression analysis indicated that the percentage difference between the curve radius and vehicle path radius is not affected by the speed, speed differential and geometric characteristics of the curve and surrounding elements. Two different margins of safety were analyzed. One is the difference between maximum permissible side friction (based on design speed) and side friction demand, while another is the difference between side friction supply (based on operating speed) and side friction demand. Generally, demands exceeded supply side friction factors on curves with radii smaller than 150 m, whereas “poor” conditions (in terms of Lamm’s consistency levels) were noted for curves under approximately 220 m. Both values are very close to the critical radius below which higher accident rates were observed according to several accident studies. Based on the results of the research, it is proposed to use a 12% smaller curve radius for the evaluation of margin of safety and that curves with radii smaller than 200 m should be avoided on two-lane state roads outside the built-up area.
1 December 2017 in Tehnicki vjesnik - Technical Gazette
This paper presents models for predicting operating speeds on tangent sections and curves of two-lane rural roads developed on continuous speed data. The data corresponds to 20 drivers of different ages and driving experiences, driving...
For effective transportation planning, land use, travel behavior, and infrastructure capacity should be optimized to support sustainable urban growth and reduce congestion. Every new site development generates traffic volume, which can affect the quality of traffic flow in the surrounding road network. Therefore, trip generation, which predicts future travel demand, is a crucial step in the traditional four-step transportation model. In this context, the main objective of this study is to develop a model for estimating vehicle trip generation due to the construction of a shopping center, which is a significant traffic generator. The survey was conducted in Split (Croatia) at five existing locations, and linear regression analysis was used to develop models for different time periods. The results indicated that vehicle trips are strongly correlated with the gross floor area of shopping centers, with a high coefficient of determination. Additionally, this study presents a comparison of measured traffic volumes with estimates using ITE Trip Generation Manual equations. The findings suggest that these vehicle trip estimates should be reduced by approximately 40%. Since no previous studies have been conducted on the impact of land use on trip generation in the Republic of Croatia, the developed models represent a first step in creating a database that should be expanded with new data. Estimating the traffic generated by a new site development is a crucial component of traffic management, as it helps planners and engineers assess its impact on the surrounding road network and implement necessary measures to ensure efficient and safe traffic flow.
4 March 2023 in Advances in Civil and Architectural Engineering