Sadettin Topçu

Dr. Sadettin Topçu

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 August 2024 in Acta Geotechnica
Verified
Journal Article
Open access
PDF file
STSadettin Topçu
Sadettin Topçu
HSHasan Savaş
Hasan Savaş
Hasan TosunHasan Tosun
Hasan Tosun
Internal erosion is one of the most important factors that cause earth structures that retain water, such as embankment dams, to collapse. Concentrated leak erosion, one of the forms of internal erosion, occurs in cracked fine-grained soils and pressurized flow conditions. To evaluate the concentrated leak erosion risk of cracks/voids, it is necessary to ascertain the erosion resistance of these materials. The erosion rate and critical shear stresses determine internal erosion resistance in concentrated leak erosion. This study determined soil’s concentrated leak erosion resistance using test equipment that allowed the flow to pass through a hole with stress-free (no loading), anisotropic-compression stress, anisotropic-expansion stress, and isotropic stress conditions. The stresses that developed in the samples’ hole wall where erosion occurred were determined with numerical modeling as pre-experimental stress conditions. The experiments were performed under a single hydraulic head on four selected cohesive soils with different erosion sensitivity. Time-dependent flow rates obtained from the test system can be used to determine hydraulic parameters, such as energy grade lines, with the help of basic theorems of pipe hydraulics in theoretical hydraulic models. Moreover, the erosion rates were quantitatively determined using the continuity equation, while critical shear stresses were qualitatively compared for concentrated leak erosion developed by the dispersion mechanism. As a result of the experiments, stress conditions influence the concentrated leak erosion resistance in the soil samples with dispersive erosion. Moreover, the shear strength in the Mohr–Coulomb hypothesis can explain the erosion resistance in these soils under stress conditions depending on the sand/clay ratio.

18 October 2021 in Geotechnical Testing Journal
Verified
Journal Article
Closed access
STSadettin Topçu
Sadettin Topçu
HTHasan Tosun
Hasan Tosun
Dispersive soils cause great damage to hydrophilic earth structures and unprotected slope surfaces because of their high erosion sensitivity. In fine-grained soils, erosion resistance decreases with increased dispersibility. The dispersion mechanism of clays is controlled by the clay mineralogy and by the physicochemical repulsive forces in the clay–water system. The erosion resistance of dispersive soils can be determined by surface and internal erosion tests. In this study, the internal erosion resistance of soils was determined by using new test equipment that allowed the flow to pass through a hole when the dispersion mechanism in fine-grained soils was activated. The experiments for this study were performed under a single hydraulic head on two different natural dispersive soils with similar clay mineralogy. In this experimental system, both uniform and fully developed flow conditions were achieved. Time-dependent flow rates obtained from the experimental system can be used to determine hydraulic parameters, such as energy grade line, at very low error rates with the help of basic theorems of pipe hydraulics in theoretical hydraulic models, which were formed using a physical hydraulic model. Moreover, the erosion rates were quantitatively determined by using the continuity equation, and critical shear stresses were qualitatively compared for internal erosion developed by the dispersion mechanism. The sand/clay ratio determined the erosion resistance and behavior of the dispersive soils.

24 April 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SKSerdar Koltuk
Serdar Koltuk
STSadettin Topçu
Sadettin Topçu
The interaction between raft foundations and soils is generally modeled with the help of linear elastic springs. The design of structural elements can only be computed when the modulus of subgrade reaction is accurately determined, which is a time-consuming process for raft foundations with relatively large sizes due to the input of many structural loads. In the present work, an approximate procedure is studied based on the relative stiffnesses of soil–foundation systems suggested by DIN—Technical Report 130. To estimate the behavior of soil–foundation systems (rigid or flexible), the limit values of relative stiffness are first determined for raft foundations on elastic soils with the stiffness moduli obtained from one-dimensional consolidation tests by using finite element analyses. Subsequently, the values of subgrade reaction moduli obtained from the FE analyses are compared and discussed with the subgrade reaction moduli determined by using the analytical method considering the relative stiffnesses of soil–foundation systems. It is shown that for a soil–foundation system with a relative stiffness ≥ 0.174, the subgrade reaction modulus obtained from the analytical method assuming a rigid system is about 1.5 to 2 times higher than that in the FE analyses. For a soil–foundation system with a relative stiffness ≤ 0.0004, the analytical method assuming a flexible system and the FE method yield a similar value of subgrade reaction modulus in the central area of the raft foundation.

15 December 2023 in Journal of Civil Engineering and Urbanism
Verified
Journal Article
Closed access
STSadettin Topçu
Sadettin Topçu
ESEvren Seyrek
Evren Seyrek

31 December 2023 in Journal of Scientific Reports-A
Verified
Journal Article
Open access
PDF file
STSadettin Topçu
Sadettin Topçu
ESEvren Seyrek
Evren Seyrek
Embankment dams may collapse because of internal erosion that develops in the crack developed in the upstream-downstream direction by hydraulic fracturing. It is known in the literature that many dams collapsed due to hydraulic fracturing. The hydraulic fracturing mechanism is defined as the propagation of an existing crack on the upstream face of the clay core under hydrostatic stresses or the formation of a new crack in low-stress zones by hydrostatic stress. The variety of materials and materials' mechanical properties generally affect the hydraulic fracturing potential. This study examined the effect of the deformation parameters (Elasticity modulus and Poisson ratio) of the impermeable curtain-function clay core material on the hydraulic fracturing potential. Normal Stress and Mohr-Coulomb methods were used to determine the hydraulic fracturing potential. The principal stress values required for these two methods were determined for the maximum cross-section of the clay-core rockfill type Çınarcık Dam by the finite element method. While the hydraulic fracturing potential is negligibly affected by the change of deformation parameters in the Normal Stress method, this effect is clearly seen in the Mohr-Coulomb method.

2 June 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
STSadettin Topçu
Sadettin Topçu
ESEvren Seyrek
Evren Seyrek
Zoned embankment dams are widely used because of their economic and hydraulic advantages. Yet, the stiffness contrast between the clay core and surrounding rockfill may induce transverse arching, reducing core stresses and increasing hydraulic fracturing susceptibility. This study aimed to develop explicit predictive equations for the minimum transverse arching ratio at the upstream side of the core and at the core centerline under end-of-construction conditions. A structured numerical database consisting of 288 two-dimensional plane-strain finite element analyses was generated by varying dam height, section geometry, clay-core elastic modulus, and Poisson’s ratio. Based on this database, Gene Expression Programming (GEP) and Multiple Linear Regression Analysis (MLRA) were used to derive predictive formulations. The GEP equations showed high predictive accuracy, with overall performance metrics of R2=0.9486, RMSE = 0.0200, MAE = 0.0159, and MAPE = 2.9797% for Rmin,ups, and R2=0.9644, RMSE = 0.0163, MAE = 0.0132, and MAPE = 1.7993% for Rmin,core. In both responses, normalized filter thickness emerged as the dominant variable. Compared with MLRA, the GEP formulations performed better, particularly for the upstream-side response. The proposed equations provide a practical alternative to repeated, time-consuming numerical analyses in preliminary designs and safety assessments.