Gabriela Lujan Brollo

Dr. Gabriela Lujan Brollo


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2017 in Thermochimica Acta
Verified
Journal Article
Closed access
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
CPCecília Tereza Weishaupt Proni
Cecília Tereza Weishaupt Proni
LPLeandro Cássio de Paula
Leandro Cássio de Paula
EZEugenio José Zoqui
Eugenio José Zoqui

1 January 2018 in Thermochimica Acta
Verified
Journal Article
Closed access
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
LPLeandro Cássio de Paula
Leandro Cássio de Paula
CPCecília Tereza Weishaupt Proni
Cecília Tereza Weishaupt Proni
EZEugênio José Zoqui
Eugênio José Zoqui

2 December 2019 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
CPC. T. W. Proni
C. T. W. Proni
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
EZEugenio José Zoqui
Eugenio José Zoqui

1 December 2019 in Calphad
Verified
Journal Article
Closed access
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
DTDaimer Velazquez Tamayo
Daimer Velazquez Tamayo
LTLuis Vanderlei Torres
Luis Vanderlei Torres
EZEugenio José Zoqui
Eugenio José Zoqui

26 September 2023 in International Journal of Metalcasting
Verified
Journal Article
Open access
PDF file
IGIzabel Da Penha Gomes
Izabel Da Penha Gomes
ABAndré Barros
André Barros
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
CSCassio Augusto Pinto da Silva
Cassio Augusto Pinto da Silva
Noe CheungNoe Cheung
Noe Cheung
EZEugenio José Zoqui
Eugenio José Zoqui
This work assesses the effect of cooling rate ( $$\dot{T}$$ T ˙ ) on the solidification kinetics and microstructural evolution of a 319 aluminum alloy with and without the addition of Al–5 wt%Ti–1wt%B grain refiner. Directionally solidified samples were produced under various cooling rates (from 0.05 to 40 °C/s). Microstructure coarsening was then quantitatively analyzed by measuring grain size (GS) and primary (λ1), secondary (λ2) and average (λL) dendrite arm spacing. The results show that polarized optical images can be used to identify dendrite fragments between neighboring primary dendrites, allowing a more accurate microstructural analysis after the addition of grain refiner. The results also show that, for a given $$\dot{T}$$ T ˙ , although GS is reduced after the addition of grain refiner, the respective values of λ1, λ2 and λL remain practically the same. In other words, the grain refiner only affects nucleation and not grain growth. Experimental growth equations are proposed to represent this behavior. Furthermore, λL is shown to be a good parameter for evaluating microstructural refinement.

9 May 2018 in Metals
Verified
Journal Article
Open access
PDF file
GBGabriela Lujan Brollo
Gabriela Lujan Brollo
CPCecília Tereza Weishaupt Proni
Cecília Tereza Weishaupt Proni
EZEugenio José Zoqui
Eugenio José Zoqui
Thixoforming depends on three factors: (a) the thermodynamic stability of the solid-to-liquid transformation in the presence of temperature fluctuations; (b) the size and morphology of the solid particles in the liquid in the semisolid state; and (c) the rheology of the semisolid slurry during formation. In this study, these parameters were characterized for an Al-Si-Cu alloy with a high Fe content (B319+Fe alloy). Fe is usually found in raw metal produced by recycling, and its removal increases processing costs. This study is an attempt to use this lower-cost alloy for the thixoforming route. Thermodynamic analysis was performed by numerical simulation (under Scheil conditions) and the application of the differentiation method (DM) to differential scanning calorimetry (DSC) curves recorded during heating cycles up to 700 °C at 5, 10, 15, 20, and 25 °C/min. The processing window was evaluated by comparing the results of the DM and those of the analysis of open-die thixoforged samples after isothermal heat treatment at 575, 582, 591, and 595 °C for 0, 30, 60, and 90 s. The microstructural and rheological behavior of the semisolid slurry was analyzed at 591 and 595 °C for all four soak times. Isothermal heat treatment caused the refinement and spheroidization of the solid phase. Good agreement between the predicted thermodynamic behavior and the microstructural behavior of the thixoformed B319+Fe alloy samples was observed. Although the alloy exhibited a coarse microstructure, it was microstructurally and rheologically stable at all temperatures and for all the soak times studied, indicating that B319+Fe is a promising raw material for thixoforming.