Department of Electronics and Communication Engineering and Department of Photonics and Nanoelectronics, Hanyang University ERICA, Ansan, Gyeonggi-do 15588, South Korea
Prof. Dr. Jong-In Shim
Department of Electronics and Communication Engineering and Department of Photonics and Nanoelectronics, Hanyang University ERICA, Ansan, Gyeonggi-do 15588, South Korea
For accurate and reliable measurement of the internal quantum efficiency (IQE) of light‐emitting diodes (LEDs), the method should be theoretically solid and experimentally simple to use without any prior assumption of physical parameters or complicated equipment. In this paper, we critically review the conventional characterization techniques for measuring the IQE of LEDs, including the methods based on temperature‐dependent electroluminescence and constant AB(C) models. After reviewing the limitations of the existing IQE measurement techniques, we present the recently proposed method based on the improved AB model, called room‐temperature reference‐point method (RTRM). The RTRM is then applied to various LED devices to show how the IQE measurement techniques can be utilized to analyze their optoelectronic performances quantitatively.
We investigate the current-dependent and temperature-dependent efficiency droops (“J-droop” and “T-droop”, respectively) in InGaN-based blue and AlGaInP-based red light-emitting diodes (LEDs). It is found that the blue and red LEDs show different droop behaviors with increasing current density and temperature. The J-droop is significant in the blue LED while the T-droop is severe in the red LED. In case of the blue LED, the carrier accumulation caused by the saturation of the radiative recombination rate is thought to increase the quasi-Fermi level rapidly, thus causing the J-droop. On the other hand, the T-droop of the red LED is influenced by redistribution of carriers due to the increased thermal energy with a small barrier height in the AlGaInP material system. The comparison of different droop characteristics of blue and red LEDs helps understand the recombination mechanisms of both LEDs and provides useful insight for improving the device performance further.
While there have been many discussions on the standard Si pn-diodes, little attention has been paid and confusion still arises on the ideality factor of the radiative recombination current in semiconductor light-emitting diodes (LEDs). In this letter, we theoretically demonstrate and experimentally confirm by using blue and infrared semiconductor LEDs that the ideality factor of the radiative recombination current is unity especially for low-current-density ranges. We utilize the data of internal quantum efficiency measured by the temperature-dependent electroluminescence to separate the radiative current component from the total current.
18 January 2018 in IEEE Journal of Quantum Electronics
We present a method of measuring the internal quantum efficiency (IQE) of light-emitting diodes (LEDs) as a function of driving current at an arbitrary temperature only with experimentally measurable quantities of optical power and current. The measurement procedure starts to find an exact value of the IQE at the reference point where the injection efficiency is considered as 100% and the radiative efficiency is calculated from the infinitesimal change of the relative external quantum efficiency (EQE). Once the IQE at the reference point is exactly known, the IQE at any other point is calculated by the relative ratio of the EQE values to the reference one. We show the theoretical formalism of the proposed method and demonstrate its validity using a commercial InGaN blue LED as an example. The comparison with the IQE obtained by the conventional temperature-dependent electroluminescence is also given for various temperatures.
We investigate the cause of the optoelectronic performance variations in InGaN/GaN multiple-quantum-well blue light-emitting diodes, using three different samples from an identical wafer grown on a c-plane sapphire substrate. Various macroscopic measurements have been conducted, revealing that with increasing strain in the quantum wells (QWs), the crystal quality improves with an increasing peak internal quantum efficiency while the droop becomes more severe. We propose to explain these variations using a model where the in-plane local potential fluctuation in QWs is considered. Our work is contrasted with prior works in that macroscopic measurements are utilized to find clues on the microscopic changes and their impacts on the device performances, which has been rarely attempted.
17 May 2019 in IEEE Journal of Quantum Electronics
As an attempt to elucidate the origin of the power-efficiency (PE) degradation at high current injection for GaInN-based light-emitting diodes, the injection current is quantitatively separated to radiative and nonradiative current components as a function of applied voltage. It is found that the conventional Shockley equation for the current-voltage curve of a Si pn diode is not adequate for the LED since the carrier transport and recombination processes are quite different from those of the Si pn diode. Hence, we propose a diode equation for an LED where the radiative and nonradiative currents are separately expressed as a function of applied voltage. By analyzing the proposed diode equation, it is concluded that the PE degradation at high injection currents is due to the increase of the junction voltage and the decrease of the internal quantum efficiency at the same time. The phenomena can be understood by the insufficient recombination rate in the active quantum wells.