Objective: This review aims to evaluate the current understanding and clinical applications of machinable ceramic‐reinforced composites (CRCs) and the emerging first generation of 3D‐printed CRCs in dental restorations. Overview: Machinable CRCs, introduced over a decade ago, have shown moderate success in short‐ to medium‐term clinical applications, particularly in low‐stress areas. However, their long‐term durability limitations, such as increased wear and marginal deterioration, restrict their use in high‐stress situations and full crowns. The first generation of 3D‐printed CRCs offers customization advantages but is still in early development and exhibits lower mechanical strength and higher wear rates than CAD‐CAM CRCs and traditional ceramics. Additionally, the classification and definitions surrounding CRCs remain ambiguous, as ADA categorizations do not clearly differentiate CRCs from ceramics, complicating clinical indication, usage, and billing practices. Conclusion: Machinable CAD‐CAM CRCs are moderately successful in low‐stress applications, while 3D‐printed CRCs show limitations in wear resistance and durability, raising concerns for their use in definitive restorations. Both require further research and clinical validation. Clinical Significance: Machinable CAD‐CAM CRCs are best suited for low‐stress applications, while 3D‐printed CRCs may be more appropriate for provisional use. Until long‐term clinical data are available, ceramics should be preferred for high‐stress or full‐coverage restorations. Clearer definitions for porcelain/ceramic and comprehensive application guidelines are urgently needed to support clinician decision‐making and improve patient outcomes.
Objectives. The purpose of this investigation was to analyze epidemiological patterns, clinical features and the management of odontogenic infections in patients undergoing treatment in a dental emergency outpatient care unit. Study design. A retrospective analysis of 58 161 case records of patients presenting to an emergency outpatient unit in Hamburg, Germany between 2000–2007 was performed. From this pool, patients with odontogenic infections were identified using an ICD-10 code, analyzing age, gender, medical co-morbidities, duration of pain, ratio of infiltrates/abscesses, affected teeth, management of infection and administered antibiotics. Results. Of the 58 161 patients, 5357 (9.2%) were identified as having odontogenic infections, with 2689 (50.2%) inflammatory infiltrates and 2668 (49.8%) abscesses. Mean age was 34.8 ± 16.8 years. As the primary site of odontogenic infection, the most significantly affected teeth were the maxillary and mandibular first molars. Patients in age-group 20–29 years (25.1%) utilized the emergency care unit more frequently than other age groups. Clindamycin was the most frequently administered antibiotic. Conclusions. Early recognition, diagnosis and management of odontogenic infections are requisite for avoiding or minimizing the development of potential complications. Strategies and evidence-based protocols should be developed within the dental ambulatory care sector, advancing interdisciplinary cooperation between general dentists and oral or maxillofacial surgeons.
24 November 2022 in Journal of Esthetic and Restorative Dentistry
Objective: To evaluate the microstructure and the influence of applying universal adhesive only versus universal adhesive with additional silane application on shear bond strength (SBS) to four different lithium disilicate ceramic (LDC) materials.Material and Methods: Specimens (n = 240, 1.5 mm thick) cut from four different CAD/CAM materials were polished and etched with 4.5% hydrofluoric (HF) acid according to manufacturers' instructions (20 s: IPS e.max CAD, n!ce; 30 s: Amber Mill, CEREC Tessera). For cementation, either universal adhesive only or silane + universal adhesive were applied before prefabricated composite cylinders were cemented using a dual‐cure resin cement. SBS testing was performed either after 24 h or after 20,000 cycles thermocycling +2 months water storage. Surfaces were analyzed with stereomicroscope for failure mode and with scanning‐electron microscopy for microstructure of the LDC. Statistical analysis of the data was performed with non‐parametric tests at α = 0.001.Result: SBS values for non‐aged specimens ranged from 29.08 to 17.87 MPa and for aged specimens from 22.24 to 3.01 MPa. SBS was significantly reduced when silane was omitted after aging, (p < 0.001). Failure mode was mostly mixed with some cohesive failures in the LDC.Conclusion: Bond strengths are highly affected by the CAD/CAM LDC and their microstructures. The application of silane after hydrofluoric etching is still essential to obtain long‐term bonding, irrespective of the presence of silane in the universal adhesive. Water degradation can significantly affect long‐term bonding to novel LDC.Clinical Significance: When using a universal adhesive for bonding to LDC restorations, the best long‐term bond is achieved if an additional application of silane precedes the universal adhesive.
1 August 2017 in The Journal of Prosthetic Dentistry
Peptide-based biomimetic treatments have gained increased attention in the dental field due to their biocompatibility and minimally invasive qualities. These biomimetic approaches can replicate the native architecture of dental tissues, thus contributing to higher success rates and improved longevity of restorations. The aim of this study was first to examine the biocompatibility and stability of an amelogenin peptide-based chitosan hydrogel (P26-CS) against salivary enzymes. Second, we aimed to evaluate its efficacy in biomimetically repairing human dental lesions in situ. White spot lesions (WSLs) in enamel and non-carious cervical lesions (NCCLs) in dentin were artificially created. Chitosan (CS) improved peptide stability, while remineralization of enamel sections with P26-CS was not impeded by salivary enzymes. The peptide was not cytotoxic, irritating, or sensitizing. Fluorescently labeled P26-CS penetrated ~300 μm into the enamel of WSLs and ~100 μm into the dentin of NCCLs. After peptide treatment, quantitative light-induced fluorescence (QLF) and microcomputed tomography (μCT) indicated a gain in mineral density of WSLs. In NCCLs, scanning electron microscopy showed that the dentin was covered by a mineral layer of needle-shaped crystals. Our results show that the repair of artificial WSLs and NCCLs was achieved by P26 peptide-guided remineralization and demonstrate its potential to repair dental lesions.