CHARLES CHEMALE YURGEL

Dr. CHARLES CHEMALE YURGEL

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 April 2023 in Metals
Verified
Journal Article
Open access
PDF file
NRNijenthan Rajendran
Nijenthan Rajendran
CYCHARLES CHEMALE YURGEL
CHARLES CHEMALE YURGEL
WMWojciech Misiolek
Wojciech Misiolek
Ricardo Alves de SousaRicardo Alves de Sousa
Ricardo Alves de Sousa
The objective of the presented work was to develop a new forging process for a pinion shaft as a component of a wind turbine. A study of near-net-shape forming using Deform 3D software was performed to reduce operational cost, time, and material scrap; enhance specific properties; increase productivity. Near-net forged products have good dimensional accuracy and continuous metal flow lines, which are characteristic of improved mechanical properties. To avoid the traditional trial-and-error experimental method, the process and tool design were accomplished with a careful and detailed numerical simulation approach. In the present work, the Finite Element Method was used to develop a process model for the existing hot forging process of the 18CrNiMo7-6 steel pinion shaft used in a wind turbine. The developed numerical process model was validated via experiment including a comparison of the metal flow lines from the FEM model with the metallography results of the forged part. Two new die designs were proposed, and the simulation results were compared to the actual process to achieve improved geometry. The results for the new geometries showed improvements in terms of the die cavity filling for the new proposed dies and better results in grain flow orientation. Compared to the initial non-optimized die, the new designs improved the mechanical properties and savings associated with the lower volume of required raw material and fewer finishing operations. Considering the applied stresses and wear in the new near-net shape, the die geometry shall be updated to accommodate more severe solicitations. Naturally, all the improvements carried out are dependent on other factors such as the conditions of the equipment, operator skills, lubrication, and other variables. A surface heat treatment is also suggested for stress relief as a reliability improvement.

17 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
JSJaques Araripe Suris
Jaques Araripe Suris
CYCHARLES CHEMALE YURGEL
CHARLES CHEMALE YURGEL
Ricardo Alves de SousaRicardo Alves de Sousa
Ricardo Alves de Sousa
The hot forging process brings significant advantages in terms of improved mechanical properties of the part compared with other processes, such as casting or machining. The metal flow in the forging process leads to texture modifications and can be macroscopically visualized by the so-called grain-flow orientation (GFO). This study showed the effect of GFO on fatigue life by using a rotational flexing fatigue test. The tests that were performed using SAE 1045H steel material, at rolling and transverse directions, showed the influence of GFO on the specimens’ mechanical properties compared with the reference samples taken from the machined rolled bar. The experimental results showed that the forged samples with the GFO in the main deformation direction presented a higher fatigue life than the other tested configurations.

16 January 2026 in International Journal of Material Forming
Verified
Journal Article
Open access
PDF file
CYCHARLES CHEMALE YURGEL
CHARLES CHEMALE YURGEL
NRNicholas Rockwell
Nicholas Rockwell
WMWojciech Misiolek
Wojciech Misiolek
FLFabio Andre Lora
Fabio Andre Lora
Ricardo Alves de SousaRicardo Alves de Sousa
Ricardo Alves de Sousa
Low-alloy steel drill bits are commonly used in the mining industry for boring holes into rocks. They are characterized by high hardenability and a good combination of mechanical properties, with minimal additions of alloying elements. As product quality improves, the market becomes more competitive. Significant growth in the use of engineering development tools has also occurred, leading to improved performance in rock drilling, oil and mineral exploration, and the search for gemstones. Due to the constant cyclical mechanical stresses applied, the expected life of drill bits is often reduced by fatigue or mechanical wear, indicating that the market consistently requires the availability of new drill bits. This work aimed to demonstrate the suitability of hot forging as a substitute for machining to manufacture the specific profile of the drill bit preform used in rock drilling. A mining-industry partner selected AISI 8640 steel, as it is widely used for drilling applications. Tests were performed with AISI 8640 as a modeling material, and the results from the forging process were used to evaluate the punch movement and consequent metal flow, as well as the filling of the part’s cavity within the forging dies. The results obtained using Elementary Plasticity Theory (EPT) allowed verification of the physical experiment with AISI 8640 steel forged parts. Following this evaluation, numerical modeling was performed and compared with the hot forging process. Formation of the hollow cavity $$\sigma_b$$ within the part and the head of the preform in the same step was assessed. As a result of this optimized process, the reduction in the initial height of the billet and the preform formation were analyzed, with the finishing of the drill bit contingent upon the machining process. This hot forging demonstrated improved material utilization compared to the machining process, highlighting the benefits of deformation through simulations.