Oliver Stübbe

Prof. Dr. Oliver Stübbe


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2020
Verified
Conference Paper
Open access
PDF file
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
MBMicha Beyer
Micha Beyer
OSOliver Stübbe
Oliver Stübbe
Additive manufacturing (AM) has provided a new aspect of manufacturing 3D objects in the past few decades. The use of AM for the production of 3D objects has accelerated the rate of designing and manufacturing. These AM techniques can be utilized in manufacturing optical, mechanical and electrical prototypes. The manufacturing of optical prototypes involves the production of spherical lens prototypes and special forms of aspheric and concentrator lenses such as fresnel lens prototypes. Different designed fresnel lens prototypes are manufactured using a transparent clear resin material and stereolithography apparatus (SLA) process. It uses a photochemical process to develop 3D structures. These manufactured fresnel lens prototypes are difficult to postprocess using hand polishing, hence they are post-processed using lacquering to get more transparency. These prototypes are tested using a laser source to evaluate the attenuation of light and focal length of manufactured fresnel lens prototypes. Similar tests using a commercially available convex lens of the same focal length are carried out. The results of these tests show that the difference between the mean of attenuation of light beam when passed through a fresnel lens prototype and the convex lens is 1 dB. The focal length of manufactured fresnel lens prototypes has a 10 mm deviation. Therefore, it is feasible to manufacture complexity and cost reduced fresnel lens prototypes using SLA and lacquering.

10 February 2025 in Coatings
Verified
Journal Article
Open access
PDF file
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
Sascha PreuSascha Preu
Sascha Preu
OSOliver Stübbe
Oliver Stübbe
Additive manufacturing of optical, electrical, and mechanical components is a beneficial approach for the rapid prototyping of components and error elimination, with short turnaround times. However, additively manufactured components usually have rough surfaces that need post-processing, particularly for optical components, where the surface roughness must be a small fraction of the wavelength. We demonstrate an innovative and economical approach by dip-coating with the same resin used for printing in a simple post-processing step, providing high transparency to the 3D-printed optical components and reducing surface roughness while achieving perfect index matching of the coating layer. The surface roughness of the 3D-printed optical components drops to 5 nm (arithmetic average) after the dip-coating process. We observed significant performance enhancements after comparing the unprocessed optical components and the dip-coated optical components, including optical transparency and a shiny surface finish for previously rough surfaces.

18 April 2021
Verified
Conference Paper
Closed access
PDF file
DSDaniel Schneider
Daniel Schneider
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
HFHolger Flatt
Holger Flatt
OSOliver Stübbe
Oliver Stübbe
RLRoland Lachmayer
Roland Lachmayer
Visible light communication (VLC) allows the dual use of lighting and wireless communication systems by modulation of illumination devices. However, to increase the performance, typically, beam-forming measures are taken creating pencil beams, thus contradicting the illumination purpose. In order to optimize the performance trade off between efficient illumination and communication, the switching capabilities of illumination LEDs are examined. Illumination LEDs with standard drivers and without beam-forming show limited applicability for communication purposes as they are not optimized for the necessary switching capability (f ≈11 MHz) and coherence. Methods to enhance the electrical current by pre-equalisation, biasing, carrier sweeping and current shaping are examined in respect to the illumination LED's communication performance. A novel driver scheme is derived which achieves considerably higher switching frequencies (f ≥100 MHz) without employing beamforming at the illumination LED. This driver is able to obtain a data rate of up to 200 Mbit/s at a distance of 3.2 m, using on-off keying (OOK) modulation technique. Therefore, it is feasible to apply the LED driver by implementing standardised illumination devices in VLC systems.

12 March 2024
Verified
Conference Paper
Closed access
PDF file
ASAkshay Manoj Shahane
Akshay Manoj Shahane
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
CWChristian Wittenbröker
Christian Wittenbröker
OSOliver Stübbe
Oliver Stübbe
Additive manufacturing enables direct prototyping of complex 3D-objects that are difficult to manufacture using conventional methods. It is widely used to fabricate cost-efficient prototypes and portrays as a bridging technology to connect different scientific and industrial fields, e.g. Engineering, Medicine, etc. Consequently, additive manufacturing finds its applications in the production of patient-specific orthoses. This paper discusses the application of the stereolithography apparatus process to develop a pressure sensor based on an optical waveguide principle to embed into a below-knee orthosis. For Orthopaedic patients, the below-knee orthosis must be adjusted to the lower leg at regular intervals due to anthropometric changes in patient’s body to achieve proper mobility and correct load. Currently, this alteration relies on the patient’s estimation of support load and is only sub-optimal. Hence, the concept of developing an intelligent orthosis with a novel embedded optical system to monitor the exact support load at the neuralgic is proposed.

27 January 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
Sascha PreuSascha Preu
Sascha Preu
OSOliver Stübbe
Oliver Stübbe
Additive manufacturing of optical, electrical and mechanical components is a beneficial approach for rapid prototyping of components and error elimination with short turn around times. However, additively manufactured components usually have rough surfaces which need post-processing, in particular for optical components where the surface roughness must be a small fraction of the wavelength. We demonstrate an innovative and economical approach by dip-coating with the same resin as used for printing, providing high transparency of the 3D-printed optical components and reduced surface roughness with perfect index matching of the coating layer in a simple post processing step. The surface roughness of the 3D-printed optical components drops to 5 nm (arithmetic average) after the dip-coating process. We observed significant performance enhancement after comparing the unprocessed optical components and dip-coated optical components, including achieving optical transparency and shiny surface finish of previously rough surfaces.

18 June 2024
Verified
Conference Paper
Closed access
PDF file
Abhijeet ShrotriAbhijeet Shrotri
Abhijeet Shrotri
CWChristian Wittenbröker
Christian Wittenbröker
SPSascha Preu
Sascha Preu
OSOliver Stübbe
Oliver Stübbe
The polyethylene oxide (PEO)-based polymer electrolytes containing lithium salts pave the way for the development of safe lithium batteries with high energy storage capacity. Enabled by the flexibly vibrating polymer matrix, the Li-ion transport occurs via hopping along and between the polymer chains. Here, terahertz (THz) time-domain spectroscopy over a frequency range extending from 0.1 THz to 7 THz is applied to investigate the conduction properties of PEO-based electrolytes with lithium salts, and to elucidate the associated dependence of the THz conductivity on the content of the added lithium salt and the electrolyte temperature. It is remarkably found that the higher the observed THz vibrational activity of the electrolyte, the higher its technologically relevant ionic conductivity.