To compare them with PTFE-40# steel tribo-pairs, the tribological properties of textured PEEK-40# (AISI 1040) steel friction pairs were researched under full-film lubrication conditions by manufacturing micro-dimples with different dimensions on the contact surfaces of 1040 steel discs using laser surface texturing (LST). After repeated tribological tests, the coefficients of friction (COFs), wear losses, and wear morphologies of the PEEK-1040 steel friction pairs were measured and analyzed. The results show that micro-dimples do not significantly reduce the average COFs of PEEK-1040 steel friction pairs when lubricated with a sufficient amount of hydraulic oil, but they do reduce the wear losses of most groups. When the dimple diameter was 250 μm, the dimple depth was 5 μm, the area ratio was 6.6%, and the mass loss of the 1040 steel disc was reduced by 90% compared to the smooth reference. In comparison to the behavior of the PTFE-1040 steel tribo-pairs, PEEK-1040 steel friction pairs can provide better tribological performance, whether smooth or dimple-textured. This study offers important insights for the design of seals in machinery.
To enhance the operational stability and service life of tapered roller bearings (TRBs), this study investigates the application of surface texturing technology using laser marking to fabricate micro-dimples with controlled diameters and distributions on the TRB outer ring. An orthogonal experimental design was implemented to systematically evaluate the effects of three key dimple parameters—diameter, depth, and angular distribution—on the tribological performance under starved lubrication. The results demonstrate that the textured surfaces significantly improve friction-reducing performance and wear resistance. Optimal dimple parameters (diameter: 200 μm, depth: 10 μm, angular interval: 0.9°) were identified, achieving a 43.6% reduction in the average coefficient of friction (COF) and a 75.7% decrease in wear loss compared to smooth bearings. These findings would offer a practical approach to enhancing the durability and operational reliability of TRBs in industrial applications.
Biomimetic surface texturing provides a promising strategy for regulating the vibration behavior of rolling bearings under starved lubrication. In this study, vein-like, elliptical, semi-elliptical, and composite textures inspired by Monstera deliciosa leaves were fabricated on the shaft-washer raceways of thrust cylindrical roller bearings at depths of 4 μm, 8 μm, and 12 μm. Tangential and normal vibration signals were analyzed using time-domain parameters, frequency spectra, power spectral density, and time–frequency maps. The results showed that both texture morphology and depth strongly affected vibration stability. Most textured bearings exhibited lower vibration responses than the smooth bearing after prolonged operation. Among the tested depths, 8 μm produced the most stable response, characterized by lower peak values, smoother root mean square curves, reduced power spectral density levels, and more uniform time–frequency energy distributions. The 8 μm semi-elliptical texture exhibited the best overall performance by suppressing transient impacts and high-frequency energy concentration. These findings indicate that vibration regulation in textured rolling bearings depends primarily on the synergistic matching between texture morphology and depth rather than texture complexity alone.
Rolling bearings operate under complex contact conditions, and their tribological and dynamic behaviors are highly sensitive to their lubrication performance. Based on previous studies on surface texturing, three types of representative textures (wholly distributed dimples, locally distributed dimples, and grooves) with optimized parameters were fabricated on the shaft washers using the laser marking method. This was done to investigate the synergistic effect of surface textures and polytetrafluoroethylene (PTFE) nano-additives on the tribological and friction-induced vibration performance of cylindrical roller thrust bearings under starved lubrication. Lubricating oils containing various mass fractions (0.5 wt%, 1.0 wt%, and 3.0 wt%) of PTFE nano-additives were prepared and employed. The coefficients of friction (COFs), wear losses, worn morphologies, and time/frequency-domain vibration responses were analyzed. The results show that the appropriate integration of surface textures and solid lubricant additives can establish a highly effective synergy for rolling bearings under starved lubrication. PTFE nano-additives significantly improved the tribological performance of the smooth bearings and those with dimples (both wholly distributed and locally distributed), with the optimal performance observed at a mass fraction of 3.0 wt%. In contrast, the tribological performance of the groove-textured bearings noticeably deteriorated with the addition of PTFE nano-particles, especially at higher mass fractions. The bearing with wholly distributed dimples exhibited the best overall tribological performance at a mass fraction of 3.0 wt%, achieving a 61.8% reduction in the average COF, a 99.6% reduction in wear loss, and significantly suppressed vibration amplitudes.