The supersonic laser deposition (SLD) of diamond/Cu composite powder is studied over a range of laser power. The deposition efficiency, coating microstructure, cohesive/adhesive bonding, phase composition, micro-hardness, and tribological property of the diamond/Cu composite coating are investigated. The results indicate that, as laser power is increased, deposition efficiency initially increases and then declines. The diamond particles distribute uniformly in the composite coating. Due to the increase of velocity ratio and total energy by laser irradiation, the cohesive/adhesive bonding of the composite coating is improved. The composite coating can preserve the phase composition of the origin powders due to the relatively low heat input during the SLD process. Slight oxidation of the Cu powder can be detected in the coatings prepared with high laser power, which has adverse effects on material deposition. The SLD-diamond/Cu composite coating has superior wear-resistance because of low friction coefficient, high micro-hardness, and uniformly distributed diamond particles.

The laser-induced hybrid hardening process integrates laser quenching and electromagnetic induction heating to overcome traditional heat treatment limitations, enhancing the depth and properties of hardened layers for applications like wind turbine bearings. This study uses Box–Behnken design (BBD) experiments to analyze key process parameters and develops response surface methodology (RSM) and whale-optimization-algorithm-optimized back-propagation neural network (WOA-BPNN) models for prediction and optimization. The WOA-BPNN model outperforms the RSM model, achieving superior predictive accuracy with R² values exceeding 0.995 for both depth and hardness, with a root mean square error (RMSE) for depth of 0.099 mm and of 1.734 HV_0.3 for hardness, and with mean absolute percentage error (MAPE) of 0.697% and 0.7867%, respectively. The WOA-BPNN model provides an effective and reliable framework for optimizing laser-induced hybrid hardening, improving production efficiency and extending component life for industrial applications.

To achieve the rapid heat dissipation of components in the industrial field, the heat dissipation coating is prepared on the surface, which is conducive to improving the service life of the parts and greatly reducing the industrial costs. In this paper, metallized diamond/Cu composite coatings were fabricated on 1060Al substrate by supersonic laser deposition. The composite coatings were prepared at a nitrogen pressure of 3.0 MPa, a scanning speed of 10 mm/s, and a 1060 nm semiconductor coupled fiber laser with different laser power. The research results show that the laser power affects the interface bonding by affecting the temperature of adiabatic shear instability during particle impact. The metallized diamond forms a good bonding at the interface through the plastic deformation of the Cu matrix. Appropriate parameters ensure that the jet does not affect the subsequent particle deposition and build a good heat transfer bridge to elevate the heat transfer efficiency. The coating prepared at a laser power of 1000 W has the highest thermal diffusion coefficient of 89.3 mm²/s and thermal conductivity of 313.72 W/(m·K), which is 8.92% higher compared to the coating prepared without laser. Experiments with thermal imaging have also demonstrated that the coating at optimal parameter transferred heat faster. Our research provides a technical guidance for rapid preparation of high-quality heat dissipation coatings in industry.

Carbon deposits on the crown of engine pistons can markedly reduce combustion efficiency and shorten service life. Conventional cleaning techniques often fail to simultaneously ensure a high carbon removal efficiency and maintain optimal surface integrity. To enable efficient and precise carbon removal, this study proposes the application of hybrid laser cleaning—combining continuous-wave (CW) and pulsed lasers—to piston carbon deposit removal, and employs response surface methodology (RSM) for multi-objective process optimization. Using the N52B30 engine piston as the experimental substrate, this study systematically investigates the combined effects of key process parameters—including CW laser power, pulsed laser power, cleaning speed, and pulse repetition frequency—on surface roughness (Sa) and carbon residue rate (RC). Plackett–Burman design was employed to identify significant factors, the method of the steepest ascent was utilized to approximate the optimal region, and a quadratic regression model was constructed using Box–Behnken response surface methodology. The results reveal that the Y-direction cleaning speed and pulsed laser power exert the most pronounced influence on surface roughness (F-values of 112.58 and 34.85, respectively), whereas CW laser power has the strongest effect on the carbon residue rate (F-value of 57.74). The optimized process parameters are as follows: CW laser power set at 625.8 W, pulsed laser power at 250.08 W, Y-direction cleaning speed of 15.00 mm/s, and pulse repetition frequency of 31.54 kHz. Under these conditions, the surface roughness (Sa) is reduced to 0.947 μm, and the carbon residue rate (RC) is lowered to 3.67%, thereby satisfying the service performance requirements for engine pistons. This study offers technical insights into the precise control of the hybrid laser cleaning process and its practical application in engine maintenance and the remanufacturing of end-of-life components.

The effective welding of a 6 mm thick TA2 pure titanium medium-thickness plate was achieved by laser–arc hybrid welding (LAHW) with helium–argon mixed shielding gas. Conducted research on the influence of helium–argon mixed shielding gas on plasma and arc characteristics during welding, and its further impact on the microstructure, internal porosity defects, tensile properties, and corrosion resistance of welded joints was explored. The study demonstrated that under the shielding gas with 75% helium, the arc width narrowed significantly from 6.96 mm to 2.61 mm, achieving a 63% reduction, which enhanced the concentration of arc heat flux density. Achieved a well-formed weld with no surface spatter and significantly reduced the internal porosity rate from 3.02% to 0.47%, which is an 84% decrease. Tensile fractures are located in the base material, all exhibiting plastic failure. The corrosion resistance of the welded joint initially increased and then decreased with the increase of helium content in the shielding gas, peaking at 75% helium content.

To address the issue of surface grain coarsening in laser-induction hybrid phase transformation of 42CrMo steel, this study investigated the effects of four pretreatment processes (quenching–tempering (QT), laser-induction quenching (LIQ), laser-induction normalizing (LIN), and laser-induction annealing (LIA)) on the austenite grain size and wear resistance after laser-induction hybrid phase transformation. The results showed that QT resulted in a tempered sorbite structure, resulting in coarse austenite grains (139.8 μm) due to sparse nucleation sites. LIQ generated lath martensite, and its high dislocation density and large-angle grain boundaries led to even larger grains (145.5 μm). In contrast, LIN and LIA formed bainite and granular pearlite, respectively, which refined austenite grains (78.8 μm and 75.5 μm) through dense nucleation and grain boundary pinning. After laser-induction hybrid phase transformation, all specimens achieved hardened layer depths exceeding 6.9 mm. When the pretreatment was LIN or LIA, the specimens after laser-induction hybrid phase transformation exhibited surface microhardness values of 760.3 HV0.3 and 765.2 HV0.3, respectively, which were 12 to 15% higher than those of the QT- and LIQ-pretreated specimens, primarily due to fine-grain strengthening. The friction coefficient decreased from 0.52 in specimens pretreated by QT and LIQ to 0.45 in those pretreated by LIN and LIA, representing a reduction of approximately 20%. The results confirm that regulating the initial microstructure via pretreatment effectively inhibits austenite grain coarsening, thereby enhancing the microhardness and wear resistance after transformation.