Alexander Diem

Alexander Diem

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2014 in Tribology International
Verified
Journal Article
Closed access
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
FAFlorian Ausserer
Florian Ausserer
SKStefan Klien
Stefan Klien
JBJosef Brenner
Josef Brenner
PFPierre Forêt
Pierre Forêt
ADAlexander Diem
Alexander Diem

16 February 2019 in Lubricants
Verified
Journal Article
Open access
PDF file
JVJoel Voyer
Joel Voyer
SKStefan Klien
Stefan Klien
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
FAFlorian Ausserer
Florian Ausserer
ADAlexander Diem
Alexander Diem
In the present study, PA6 polymers with and without solid lubricant inclusions were investigated against S1100QL steel surfaces that had different surface roughness values—a very high surface roughness (Rz ≈ 40 µm) and a low surface roughness (Rz ≈ 5 µm). Static and dynamic friction coefficients were analysed under a series of nominal contact pressures (2.5 to 40 N/mm2) considering the influences of polymer water saturation, temperature, counter-body surface roughness and lubrication. Mechanisms for the observed influences of the respective parameters are provided and are interpreted from the view of the adhesive and deformative contributions to the friction force.

1 October 2017 in Tribology International
Verified
Journal Article
Closed access
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
MLMarco Lüchinger
Marco Lüchinger
KKKerstin Kern
Kerstin Kern
SKStefan Klien
Stefan Klien
FAFlorian Ausserer
Florian Ausserer
WTWolfgang Tillmann
Wolfgang Tillmann

16 November 2017 in Lubricants
Verified
Journal Article
Open access
PDF file
JVJoel Voyer
Joel Voyer
FAFlorian Ausserer
Florian Ausserer
SKStefan Klien
Stefan Klien
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
ADAlexander Diem
Alexander Diem
It is well known that elastomers usually possess poor dry sliding friction properties due to their highly adhesive character. In order to overcome this problematic behavior in industrial applications, interfacial materials such as oils, greases, coatings, or lacks are normally used in order to separate or to functionalize the contact surfaces of elastomers. Alternatively, the high adhesion tendency of elastomers may be explicitly reduced by modifying the elastomer composition itself or by enabling a reduction of its effective contact area through, for example, surface laser texturing. This second approach, i.e., the reduction of the adhesive character of elastomers through laser structuring, will be the main topic of the present study. For this purpose, different micro-sized grooved structures were produced on flat injection molds using an ultra-short pulsed laser. The micro-structured molds were then used to produce injection molded micro-ridged Liquid Silicone Rubber (LSR) sample pads. The investigations consisted firstly of determining the degree of replication of the mold micro-structures onto the surface of the LSR pads and secondly, to ascertain the degree of reduction of the friction force (or coefficient of friction) of these micro-ridged LSR pads in comparison to the benchmark (unstructured LSR pads) when tested under dry conditions against Aluminum alloy (Al-6082) or PA6.6-GF30 plates. For this second part of the investigation, the normal force (or contact pressure) dependency of the coefficient of friction was determined through stepwise load increasing friction tests. The results of these investigations have shown that the production of micro-ridged surfaces on LSR pads through laser structuring of the injection molds could be successfully achieved and that it enables a significant reduction of the friction force for low normal forces (or contact pressures), where the component of adhesion friction is playing an important and determining role in the overall friction behavior of the LSR elastomer.

28 April 2018 in Lubricants
Verified
Journal Article
Open access
PDF file
MLMarco Lüchinger
Marco Lüchinger
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
KKKerstin Kern
Kerstin Kern
MBMichael Baumgartner
Michael Baumgartner
SKStefan Klien
Stefan Klien
WTWolfgang Tillmann
Wolfgang Tillmann
This paper presents a systematic procedure for the development of a constitutive model of friction with focus on the application in bulk metal forming simulations. The empirically based friction model describes friction as a function of sliding distance and the most relevant friction influencing parameters. The latter were determined by means of designed experiments. An optimal friction model is obtained as a trade-off between model accuracy and complexity by using stepwise nonlinear regression and a modified version of the Akaike information criterion. Within this study, the procedure is applied to determine a friction model for tube drawing. However, the same approach can also be used for modeling friction of any other bulk metal forming process.

1 September 2018 in Wear
Verified
Journal Article
Closed access
Igor VelkavrhIgor Velkavrh
Igor Velkavrh
FAF. Ausserer
F. Ausserer
SKS. Klien
S. Klien
JVJoel Voyer
Joel Voyer
ADAlexander Diem
Alexander Diem
FHF. Hofer
F. Hofer