Yan Long

Dr. Yan Long


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 April 2018 in Materials
Verified
Journal Article
Open access
PDF file
YLYan Long
Yan Long
KSKai Su
Kai Su
JZJinfu Zhang
Jinfu Zhang
XLXiaobiao Liang
Xiaobiao Liang
HPHaiyan Peng
Haiyan Peng
XLXiaozhen Li
Xiaozhen Li
A NbMoTaWVTi refractory high entropy alloy (HEA) has been successfully synthesized by mechanical alloying (MA) and spark plasma sintering (SPS). The microstructure and mechanical properties of this alloy are investigated. It is observed that only two types of body-centered cubic (BCC) solid solutions are formed in the powders after ball milling for 40 h. However, a new face-centered cubic (FCC) precipitated phase is observed in the BCC matrix of bulk material consolidated by SPS. The FCC precipitated phase is identified as TiO, due to the introduction of O during the preparing process of HEA. The compressive yield strength, fracture strength, and total fracture strain of the consolidated bulk HEA are 2709 MPa, 3115 MPa, and 11.4%, respectively. The excellent mechanical properties can be attributed to solid solution strengthening and grain boundary strengthening of the fine-grained BCC matrix, as well as the precipitation strengthening owing to the formation of TiO particles.

1 February 2022 in Vacuum
Verified
Journal Article
Closed access
HPHaiyan Peng
Haiyan Peng
ZKZhixin Kang
Zhixin Kang
YLYan Long
Yan Long
LZLi Zhou
Li Zhou

2 October 2023 in Materials & Design
Verified
Journal Article
Open access
YLYan Long
Yan Long
WMWenxing Meng
Wenxing Meng
FVFlorian Vogel
Florian Vogel
GLGuiqi Li
Guiqi Li
LZLijing Zhang
Lijing Zhang

29 October 2020 in Frontiers in Materials
Verified
Journal Article
Open access
YLYan Long
Yan Long
GLGuiqi Li
Guiqi Li
XLXiaobiao Liang
Xiaobiao Liang
HPHaiyan Peng
Haiyan Peng
A series of fine-grained FeCoNi(CuAl)x (x=0, 0.4, 0.6, 0.8, 1.0) medium-entropy alloy (MEA) and high-entropy alloys (HEAs) were fabricated by Mechanical Alloying (MA) and Spark Plasma Sintering (SPS). The effect of Al and Cu content (x) on phase composition, microstructure and mechanical properties of the alloys was investigated. Experimental results show that the crystal structure of FeCoNi(CuAl)x alloy transforms from single FCC phase for x=0 to FCC+BCC duplex phases for x=0.4~1.0, with the fraction of BCC phase gradually increasing with the increase of x. Adding a low content of Al and Cu elements to FeCoNi alloy can significantly hinder the grain growth during sintering process, the average grain size of FCC phase decreases from 0.95 to 0.30 µm at x=0.4. However, the grain sizes of FCC and BCC phases gradually grow up when x increases from 0.4 to 1.0. The variation in grain size indicates that the atomic diffusion rate of sintered alloy may be influenced by the sluggish diffusion effect in HEA as well as the content of Al and Cu with lower melting points. Mechanical properties of the HEAs are mainly affected by the volume fraction of BCC phase. The compressive yield strength and hardness of HEAs are improved at first and then slightly reduced, while the plasticity drops down continuously with the increase of x. The bulky HEA achieved excellent comprehensive mechanical properties with a compressive yield strength of 1467.7 MPa and plastic strain to failure of 24.9 % at x=0.6, due to the fine duplex microstructure.

20 September 2022 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
YLYan Long
Yan Long
KLKebo Liao
Kebo Liao
XHXiaolong Huang
Xiaolong Huang

4 July 2020 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
YLYan Long
Yan Long
WZWeihua Zhang
Weihua Zhang
LPLiang Peng
Liang Peng
HPHaiyan Peng
Haiyan Peng
XLXiaozhen Li
Xiaozhen Li
XHXiaolong Huang
Xiaolong Huang