Hennadii Viktorovich Shabanov

Mr. Hennadii Viktorovich Shabanov

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 March 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YAYurii Mschailovich Andrieiev
Yurii Mschailovich Andrieiev
DBDmytro Breslavsky
Dmytro Breslavsky
HSHennadii Viktorovich Shabanov
Hennadii Viktorovich Shabanov
Konstantin NaumenkoKonstantin Naumenko
Konstantin Naumenko
Holm AltenbachHolm Altenbach
Holm Altenbach
New analytical solutions for the inverse kinematics problem of a 6R manipulator are proposed. Based on the assumption that the rotation axes of the last three links intersect at a common point, the problem is divided into orientation and transition problems. The position of the common point and the rotation angles of the first three links are determined using the equations of motion of the output link. A matrix equation for the rotation angles of the last three links is formulated. Solutions to the inverse kinematics problem are obtained for three models. In the first two, the rotation axis of the fourth link may not intersect the vertical rotation axis of the first. In the third model, the rotation axis of the fourth link intersects neither the vertical rotation axis of the first link nor the intersection point of the axes of the last two links. For all models, an analytical solution in closed form is obtained from the geometry of the mechanism. The solution for the third requires a preliminary search for the root of the transcendental equation for the rotation angle of the fourth link. Illustrative examples of calculations for a specific manipulator are given.

24 December 2024 in Bulletin of the National Technical University «KhPI» Series: Dynamics and Strength of Machines
Verified
Journal Article
Closed access
PDF file
YAYurii Mschailovich Andrieiev
Yurii Mschailovich Andrieiev
HSHennadii Viktorovich Shabanov
Hennadii Viktorovich Shabanov
This article proposes an algorithm for solving the inverse kinematics problem of a six-degree angular manipulator based on the ABB robot model. The algorithm is based on analytical derivations obtained by the authors, which consist of a sequence of expressions that allow determining all six rotation angles of the kinematic pair parts that connect the chains by a given law of movement of the output chain – the gripper. Initially, the law of its movement – functions of time of Cartesian coordinates of the pole and orientation parameters – is determined from the conditions of performing a production task by the gripper. Any point of the gripper can be chosen as the pole. Quaternion or rotation matrix can be used as orientation parameters. It is shown how a rotation matrix and quaternion can be constructed according to the laws of change of Cartesian coordinates of three gripper points. A distinctive feature of the manipulator discussed here is the presence of a common rotation axis point for the last three chains. This allows determining the law of movement of this point from the law of movement of the gripper. After which the laws of change of rotation angles of the first three chains are uniquely determined. At the same time, the orientation task of these chains is solved. To determine the angles of the last three links, a matrix or quaternion equation is compiled, based on the equivalence of two sequences of chain rotations. The first sequence is a combination of already known rotations from the third chain through the second and first chain to the absolute coordinate system and, finally, from the absolute system to the gripper. The parameters of these rotations are known. The second sequence consists of 3 rotations at unknown angles of the last three chain from the third again to the gripper. These unknown angles are determined from such an equation. The presentation of the proposed algorithm takes into account the ABB manipulator but can be applied to manipulators of the PUMA class. The algorithm is implemented using a special computer algebra system KidyM and a developed C++ program, which uses OpenGL and SolidWorks engineering graphic packet that allow 3D visualization of the calculation results.

19 June 2026 in Bulletin of the National Technical University "KhPI". Series: Mathematical modeling in engineering and technologies
Verified
Journal Article
Closed access
YAYurii Mschailovich Andrieiev
Yurii Mschailovich Andrieiev
HSHennadii Viktorovich Shabanov
Hennadii Viktorovich Shabanov
This article presents the development of an analytical algorithm for solving the inverse kinematics problem for angular manipulators with six degrees of freedom of the PUMA-560 type, previous versions of which were presented by the authors in previous publications. The algorithm is based on thePieper condition, according to which the axes of rotation of the last three links intersect at a single point. This makes it possible to decompose theproblem of determining the generalized coordinates of the manipulator into two subproblems: a positioning problem, i.e. placing the wrist center at aprescribed point, and an orientation problem, i.e., aligning the end-effector with a prescribed spatial orientation. For each instant of time, these prescribedposition and orientation parameters are determined by the requirements of the manipulator’s operating task. Such a decomposition reduces the problem of determining all six relative joint angles to the analytical determination of only three unknowns within each subproblem. For manipulatormodels that fully satisfy the Pieper condition, both subproblems are solved exactly by the closed-form formulas proposed in the paper. For models inwhich the Pieper condition is satisfied only partially, namely when the axes of the fifth and sixth links intersect but their intersection point does not coincide with the axis of rotation of the fourth link, the positioning and orientation problems are solved within a simple iterative procedure for evaluatingthe rotation angle of the fourth link. It is shown that, for the models considered, this process converges in three iterations. The orientation problem itselfis solved here using quaternion equations and is therefore free from singularity-related degeneracy issues. The performance of the proposed algorithmis demonstrated by solving the inverse kinematics problems for three manipulator models: the PUMA-560, ABB (IRB 460), and a manipulator developed by Vertical. The main differences between the proposed algorithm and the authors’ earlier approaches are the use of more transparent geometric reasoning, the inclusion of cases involving violations of the Pieper condition, and the application of quaternions to solve the orientation problem. The derived formulas and algorithms were verified by comparing the results of the forward and inverse kinematics solutions for the three robot models.

30 January 2025 in Bulletin of the National Technical University "KhPI". Series: Mathematical modeling in engineering and technologies
Verified
Journal Article
Open access
PDF file
YAYurii Mschailovich Andrieiev
Yurii Mschailovich Andrieiev
OHOleksii Oleksandrovych Holovnia
Oleksii Oleksandrovych Holovnia
HSHennadii Viktorovich Shabanov
Hennadii Viktorovich Shabanov
The problem of automatically selecting the configuration of a robot manipulator from all possible configurations based on the evaluation of energy consumption during the operation process when performing a specific gripping movement is considered. Using the example of a welding manipulator with six degrees of freedom, formulas for the analytical computer solution of the inverse kinematics problem for a wide range of PUMA-type manipu- lators are presented. A distinctive feature of this algorithm is that each configuration of the manipulator links is defined by an individual value of one parameter. This allowed for the automatic generation of several configurations in the computer’s memory using one model description in a specialized computer algebra system, KiDyM (SCCA KiDyM). By modifying the existing algorithm for solving the inverse dynamics problem, which involves determining the movement of generalized coordinates by previously solving the inverse kinematics problem, it was possible to merge these two tasks into one. The first task allows for obtaining the laws of changing the rotation angles of the links for all configurations based on a given gripping motion. The second calculates the driving moments in the kinematic pairs immediately for all possible configurations of the mechanism and selects the optimal one with the minimum energy expenditure. Afterward, the corresponding movement of the manipulator can be implemented according to the obtained laws of angle changes. Examples of calculations for manipulator mechanisms are provided. A significant achievement of the work is the development of an analytical algorithm for solving the inverse kinematics problem for a wide range of PUMA-type manipulators using quaternions to define and obtain the orientations of the mechanism links. Thus, the obtained algorithm does not degenerate for any robot positions.