Lightweight component design is effectively achievable through sandwich structures; many past research studies in the aerospace and racing sectors (since the 1920s) have proven it. To extend their application into the automotive and other transport industries, manufacturing cycle times must be reduced. This can be achieved by sandwich materials made of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widen the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). Manufacturing defects like wrinkling and surface waviness should be minimised to achieve high reproducibility of the sandwich components. Studying different manufacturing parameters and their influence on the final part is complex and challenging to analyse through experiments, as it is time-consuming. Therefore, a finite element (FE) modelling approach is implemented to reduce such efforts. Initially, a thermoforming model is developed and validated with experimental results to check its reliability. Further, different simulations are performed to optimise the novel sandwich-forming process. In this study, a thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used, and its numerical model was executed in LS-DYNA software release R11.2.1.
Within this study, the impregnation behavior and resulting mechanical properties of unidirectional flax fiber-reinforced polyamide 11 biocomposites were investigated. Therefore, different grades of bio-based polyamide 11 have been evaluated regarding their eligibility as composite matrix material. The production of the unidirectional flax fiber-reinforced biocomposites was investigated using a continuous film-stacking method. It was found that the flow behavior of the polyamide 11 matrix polymer significantly affected the impregnation quality and the resulting mechanical properties as tested by tensile and bending tests. A lower shear viscosity and stronger shear thinning behavior led to better impregnation, a 15% higher stiffness, and 18% higher strength. This was also analyzed with morphological analysis by scanning electron microscopy. Additionally, the effect of the fiber volume content of the flax fibers on the mechanical properties was tested, showing a positive correlation between the fiber content and the resulting stiffness and strength, leading to an increase of 48% and 55%, respectively. In result, a maximum Young’s modulus of 16.9 GPa and tensile strength of 175 MPa at a fiber volume content of 33% was achieved. Thus, the unidirectional flax fiber-reinforced polyamide 11 biocomposites investigated can be a sustainable construction material for lightweight applications, e.g., in the automotive industry.
Polyamides have been established in the field of technical applications for many years, and offer a large range of application options, owing to their various structural forms and correlating properties. This chapter exclusively focuses on semi-crystalline, aliphatic polyamides, which are especially employed in injection molding, extrusion, and thermoforming. An in-depth look at the processing of semi-finished textile products will not be provided here, but remains of great significance for polyamides as a whole.
Since industrialization, the demand for fossil fuels, such as oil, natural gas, and coal have increased. This increased prices and greenhouse gases in the atmosphere. One of the most important tasks of climate protection is to reduce CO2 emissions. Existing and future technologies could reduce CO2 emissions through new sources and efficient use of energy. This could at least stabilize the climate and slow down the pace of climate change. Renewable resources are effective and interesting alternatives to fossil fuels and resulting products. Energy forms, processes, and services enhance the value-added potential of agriculture and industry. The development of new plastics, especially biodegradable biopolymers, may be the only solution to environmental damage caused by non-degradable plastics. With bio-based polymers new functionalities are achieved. These include biodegradability, compostability, and carbon footprint. The use of bioplastics can create a natural cycle (see Fig. 1.1), in which plastics produced from renewable raw materials can later be recycled or returned to nature.
Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.