The primary objective of this study is to enhance surface coating characteristics and reduce the dilution rate of AZ61 magnesium alloy coated with Stelcar alloy powder through laser cladding. A Taguchi (L16) orthogonal experimental design employed to analyze the effects of scanning speed, laser power, powder feed rate, and gas flow on wear volume, dilution rate and micro-hardness. Signal-to-noise ratios were calculated for each parameter to identify their individual effects on the responses. The findings indicated that powder feed rate predominantly influenced wear volume, accounting for 88.18% of its variation, while scanning speed has the highest influence on dilution rate (73.20%), and laser power significantly affected micro-hardness (84.60%). The optimized processing parameters were identified as a scanning speed of 11 mm/s, a laser power of 1.3 kW, a powder feed rate of 40 g/min, and a gas flow rate of 380 L/h. These parameters yielded a minimum wear volume of 0.8427 mm3, a dilution rate of 18.21%, and a maximum micro-hardness of 678.07 HV. This study utilized grey relational analysis to determine the optimum processing parameters, which simultaneously reduced wear volume, minimized dilution rate and enhanced micro-hardness.
3 April 2024 in Indian Journal of Science and Technology
Objective: To examine the tribological and mechanical characteristics of the AZ61 alloy reinforced with Stelcar alloy powder by surface modification through laser cladding. Methods: Surface modification was done by using a laser cladding machine, where the input parameters including Scanning Speed (SS), Laser Power (LP) and Powder Feed Rate (PFR) were adjusted. Experimental design followed a L9 Taguchi approach, and optimization of input parameters for the surface modified AZ61 alloy reinforced with Stelcar alloy particles was achieved using Grey Relational Analysis (GRA). Output responses, namely wear volume and micro hardness were measured to assess the effectiveness of the optimization process. Findings: From the results obtained through the experiments, powder feed rate contributes to 82.81% of the variability in wear volume, whereas the laser power mostly impacts micro hardness; influencing it by 89.46% confirmed with ANOVA. In order to determine the optimal processing parameters among various objectives, this research applies the grey relational method. The results showed that the wear volume and micro hardness of the composite were significantly affected by the Stelcar reinforcement. Employing Grey relational analysis combined with several optimization objectives into a transparent method, resulting in a clad material with the lower wear volume and higher micro hardness. The optimized processing parameters predicted grey relational grades with an error rate of 1.39% and a significant contribution of 63.60% from laser power. This study confirmed that multi-objective optimization could enhance laser-cladded surface mechanical characteristics and laid out the theoretical foundation for this approach. Novelty: This study introduces an innovative approach to surface modification by employing the laser cladding technique to reinforce Stelcar alloy particles, thereby creating a dense coating on the substrate. Keywords: Laser Cladding, AZ61 magnesium alloy, Stelcar alloy, Coating, Optimization
This study investigates the optimization of laser cladding parameters to enhance the surface properties of AZ61 magnesium alloy using Inconel 625 powder reinforcement. Due to the alloy’s inherent limitations such as low wear and corrosion resistance, surface modification through laser cladding offers a promising solution for improving functional performance. An L16 orthogonal array based on the Taguchi method facilitated the evaluation of four process parameters namely laser power, scanning speed, powder feed rate, and gas flow rate. The measured responses included microhardness, dilution rate, and wear volume. Analysis of variance and signal-to-noise ratios indicated that laser power significantly influenced microhardness (84.42%), scanning speed affected dilution rate (87.13%), and powder feed rate predominantly impacted wear volume (89.42%). Grey Relational Analysis identified the optimal parameter combination that achieved maximum hardness, minimum wear, and minimal dilution. The optimized settings produced a low prediction error of 1.89% in the grey relational grade. These findings confirm the effectiveness of Grey Relational Analysis based multi-response optimization in enhancing surface quality and wear resistance of magnesium alloys, making the process well-suited for lightweight applications in automotive and aerospace components.