We developed a heart-on-a-chip platform that integrates highly flexible, vertical, 3D micropillar electrodes for electrophysiological recording and elastic microwires for the tissue’s contractile force assessment. The high aspect ratio microelectrodes were 3D-printed into the device using a conductive polymer, poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). A pair of flexible, quantum dots/thermoplastic elastomer nanocomposite microwires were 3D printed to anchor the tissue and enable continuous contractile force assessment. The 3D microelectrodes and flexible microwires enabled unobstructed human iPSC-based cardiac tissue formation and contraction, suspended above the device surface, under both spontaneous beating and upon pacing with a separate set of integrated carbon electrodes. Recording of extracellular field potentials using the PEDOT:PSS micropillars was demonstrated with and without epinephrine as a model drug, non-invasively, along with in situ monitoring of tissue contractile properties and calcium transients. Uniquely, the platform provides integrated profiling of electrical and contractile tissue properties, which is critical for proper evaluation of complex, mechanically and electrically active tissues, such as the heart muscle under both physiological and pathological conditions.
14 September 2022 in Journal of Materials Chemistry A
Highly stretchable and flexible symmetrical supercapacitors are constructed from conductive polymer-infused electrospun microfibers and freeze/thawed PVA-H2SO4 gel electrolyte.
Plant pathogen zoospores play a vital role in the transmission of several significant plant diseases, with their early detection being important for effective pathogen management. Current methods for pathogen detection involve labour-intensive specimen collection and laboratory testing, lacking real-time feedback capabilities. Methods that can be deployed in the field and remotely addressed are required. In this study, we have developed an innovative zoospore-sensing device by combining a microfluidic sampling system with a microfluidic cytometer and incorporating a chemotactic response as a means to selectively detect motile spores. Spores of Phytophthora cactorum were guided to swim up a detection channel following a gradient of attractant. They were then detected by a transient change in impedance when they passed between a pair of electrodes. Single-zoospore detection was demonstrated with signal-to-noise ratios of ~17 when a carrying flow was used and ~5.9 when the zoospores were induced to swim into the channel following the gradient of the attractants. This work provides an innovative solution for the selective, sensitive and real-time detection of motile zoospores. It has great potential to be further developed into a portable, remotely addressable, low-cost sensing system, offering an important tool for field pathogen real-time detection applications.
The field of wearable and implantable bioelectronics is rapidly emerging for biological sensing, medical monitoring and treatment. Among the conducting polymers, poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) stands out as a widely studied and commercially available material extensively employed in flexible bioelectronic applications. Nonetheless, PEDOT:PSS exhibits restricted stretchability, typically withstanding less than 10% strain, and its stability in aqueous environments is also limited. Furthermore, PSS is hygroscopic and acidic which, may contribute to the deterioration of electronic devices. Here we report on novel stretchable PEDOT-based electrodes, where PSS is replaced with a highly elastomeric, macromolecular dopant. Specifically, sulfonated polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (sSEBS) was used as a co-dopant to PEDOT in a chemical oxidative polymerisation of PEDOT with various ratios of sSEBS:EDOT. Successful sulfonation of SEBS and synthesis of PEDOT:sSEBS composites were confirmed by means of FTIR and Raman spectroscopy. PEDOT:sSEBS composites were processed into dispersions in chloroform and characterised by dynamic light scattering. The free-standing films of PEDOT:sSEBS were prepared and investigated for their mechanical properties and in situ resistance. The optimised mass ratio of PEDOT:sSEBS (1 : 2 mass : mass) produced films that were highly stable in aqueous solutions, with a conductivity of 0.15 ± 0.03 S cm−1 and stretchability of greater than 100% elongation at break. Electromyography (EMG) using the fabricated films demonstrated an application of the PEDOT:sSEBS films in wearable bioelectronics. The produced PEDOT:sSEBS films overcome some of the important deficiencies of extensively utilised PEDOT:PSS.
Wearable and implantable devices play a crucial role in clinical diagnosis, disease treatment, and fundamental research on the body's electrophysiology and biochemical processes. Conducting polymers are emerging as promising solutions to surpass the limitations of traditional metal‐based electrodes, offering enhanced conformability, and stretchability. However, current microfabrication techniques of CP electrodes have a number of limitations. In this study, a novel wet‐printing technique is developed for the fabrication of highly stretchable poly(3,4‐ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) microelectrodes. The wet‐printing, conducted in a liquid coagulation bath, has the advantages of being non‐contact, easy and fast to perform, and capable of printing low‐viscosity inks. Wet‐printing of PEDOT:PSS lines with a width of ≈20 µm is demonstrated. By adding D‐sorbitol as a plasticizer, an ultra‐high stretchability of PEDOT:PSS electrodes, of more than 720% is achieved while the electrodes remained conductive and strain‐insensitive up to high strains. The use of PEDOT:PSS wet‐printed electrode arrays for the electrophysiological recording from the stomach is demonstrated. The stretchable electrodes conformed swell to the tissue and recorded comparable electrophysiological signals to Au‐plated electrodes in porcine and rodent animal models. The wet‐printing approach to fabricating flexible and stretchable electrode arrays using low‐viscosity, conducting inks holds promise for applications in conformable electronics.