Cemalettin AYGÜN

Dr. Cemalettin AYGÜN

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 June 2024 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
ESElvin Saylan
Elvin Saylan
CACemalettin AYGÜN
Cemalettin AYGÜN
Within the scope of this study, a thermoeconomic analysis was carried out for Akkuyu Nuclear Power Plant (ANPP), the first nuclear power plant of Türkiye. As a result of the analysis, it is aimed to reduce the cost of energy production and prevent thermal pollution at the same time by converting the heat discharged into the environment into useful heat due to the working principle of NPP. Thermodynamic analysis was performed in the Engineering Equation Solver (EES) program using equipment values equivalent to ANPP. Cost analysis was performed using the specific exergy costing (SPECO) method, which is based on the second law of thermodynamics and is the most widely used cost analysis method. The study concludes that the energy efficiency is 35%, while the economic analysis shows that the best case has an exergy efficiency of 68% with a payback period of 7–8 years, and an electricity cost of $0.0196 per kWh. It is possible to use the heat discharged from the plant indirectly in district heating (heating, hot water needs of the lodgings, guesthouses in the facility), greenhouse heating, agricultural drying and heating, considering the geographical conditions and livelihood of the region. Thus, 68% of the waste heat was utilized, the unit cost of the energy produced was reduced and at the same time thermal pollution was reduced at the same rate. The results of the study can contribute to the efforts preventing energy waste, thermal environmental pollution, and reducing greenhouse gas emissions. Additionally, it could aid in the development of more energy-efficient and environmentally friendly power generation systems, including pioneering nuclear power plants in developing countries.

23 October 2024 in Ocean & Coastal Management
Verified
Journal Article
Closed access
HHHürol Hocek
Hürol Hocek
DYDevran Yazır
Devran Yazır
CACemalettin AYGÜN
Cemalettin AYGÜN
ÜÖÜnal Özdemir
Ünal Özdemir

28 April 2023 in Uluslararası Muhendislik Arastirma ve Gelistirme Dergisi
Verified
Journal Article
Open access
PDF file
ITİkram Taşdemi̇r
İkram Taşdemi̇r
CACemalettin AYGÜN
Cemalettin AYGÜN
Todays, the increasing success rates, and intensity of use of implant applications have attracted attention in the field of dentistry to dental implants. In this study, the temperature and stress distribution in a dental implant was modeled in three dimensions using the commercial software Ansys, which uses the finite element method. The changes in the implant prosthesis were investigated by applying a 100N load to the model and a temperature of 45o C and 10o C, respectively. The temperature input condition was accepted as the temperature of freshly taken food/beverage from the stove for the highest temperature and the temperature of freshly taken out of the refrigerator for the lowest temperature. As a result of the analyzes (Fluid Flow), it was observed that the implant prosthesis didn’t conduct heat to the tooth root at 45o C and 10o C. As a result of the von Mises stress distribution and total deformation analysis under a load of 100 N, it was determined that the tensile and compressive strength was good (48.17 MPa), and most of the applied load was supported by the artificial tooth crown. The chewing force applied due to its structure from the tooth geometry causes non-homogeneous stress distribution in all axes. Thus, it reveals that mechanical compatibility is of great importance as well as biocompatibility. Titanium alloys (Ti-6Al-4V), which are frequently used in tooth crowns and tooth roots, cause differentiation in bone structure together with the formation of a protective oxide layer. Considering the loss of bone volume and resorption diseases, especially during the osteoporosis/menopause, it is possible that a problem may occur at the implant-bone interface.

15 May 2024 in Black Sea Journal of Engineering and Science
Verified
Journal Article
Closed access
MAMithat Akgün
Mithat Akgün
CACemalettin AYGÜN
Cemalettin AYGÜN
MAMehmet Akgün
Mehmet Akgün
ETEmre TURAN
Emre TURAN
This study examines the impact of drying Levant quality hazelnut samples, including husk and shell, using hot air heated by solar panels at a constant speed of 6 m/s. The study also investigates the impact of collector irradiation absorption surface geometries on hazelnut drying time. A solar collector with four types of air duct geometry was used to dry hazelnuts. The radiation-absorbing surface of the air duct was manufactured flat, and three different trapezoidal geometries (30, 45 and 60 angles) were used. The mass losses of hazelnuts were measured and determined at regular intervals. In addition, the total phenolic content, the DPPH radical scavenging activity, the FRAP, the free fatty acid content, the peroxide value and the moisture content were measured. For the purpose of comparison, some of the products have been dried by means of unheated air at ambient temperature. The pre-drying process (withering process) to separate the hazelnuts from husk, only took 1.5 days (14 h excluding night). In these systems, the shelled fresh hazelnuts, separated from the husk, fell below the equilibrium moisture content of 6% in 2 days (except for 18 h at night). It was found that the most suitable collector geometry for all the parameters studied in the drying of hazelnuts with solar collectors was 45 degrees, and that other geometries could be used in terms of food properties.