In this paper, a homogenous pure Barium Titanate with formula (BaTiO3) was prepared from pure Barium Carbonate (BaCO3) and titanium dioxide (TiO2) using the solid-state reaction technique, were used as raw materials having micro size by mixing of molar ratio [1:1], the powder was calcined at temperatures (900-1350) °C. The solid-State reaction can consider as an attractive process realistic alternative to the expensive wet-chemical route, according to X-ray diffraction, all of the peaks of Barium Titanate powder were perfectly suited to the positions of the peaks of the standard tetragonal phase in the pattern for this process. And with preferred crystalline size for the powder calcined at 1350 °C manifested the best results, where all the peaks indicate the formation of Barium Titanate completely. In addition, each BaTiO3 Nanopowder was compared to a micro powder that had been manufactured, by conducting x-ray diffraction, diffraction peaks undergo shifting toward higher angle to the high value of 2Ө, and Nano powder particles are smaller than micro powder particles. And this refers to a decrease in lattice parameters, in terms of the peaks of the Nano powder preceding the peaks of the micro powder of BaTiO3 and that match the result that is obtained by scanning electron microscopy (SEM).
15 March 2025 in Experimental and Theoretical NANOTECHNOLOGY
This study investigates the behavior of epoxy resin reinforced by aluminum particles to study some mechanical properties of metal-reinforced polymer composites (PMCs). Firstly, preparation of an epoxy sample, then the reinforcement of the matrix by 5% weight fraction of glass-fiber, then preparation of hybrid samples with 5% weight fiber glass + different concentrations of aluminum, and finally testing tensile, flexural, hardness, and impact properties of the samples in order to test the mechanical properties of the samples. The main reason for selecting this study is as a practical application of plastic natural gas (CNG) cylinders, which consist of epoxy and glass fibers. Reinforced these materials with aluminum powder to improve their properties and to study the effect of the weight fraction of aluminum on some mechanical properties. The results showed that the mechanical properties (tensile strength, modulus of elasticity, flexural strength, flexural modulus, hardness, impact strength, and flexural toughness) increased when increasing the concentrations of reinforcing. The composite materials have the highest value of these properties (EP+5% Eglass+0.98% Al) compared with other percentages.
In this research, coffee beans powder was used as a natural material and their effect was studied as a reinforcement material on the composite material, where e In this research, coffee beans powder was used as a natural material and their effect was studied as a reinforcement material on the composite material, where e
The shift toward eco-friendly sustainable materials has increased the search for reinforcements obtained from agricultural and domestic waste. Development of composites with calcined eggshell powder and millet stalk fibers is within the scope of green sustainable composites. The purpose of this research is to fabricate epoxy composites using these waste materials with the goal of achieving sustainability for skateboards. Six samples of the composite were made with different amounts of epoxy resin, calcined eggshell powder and millet stalk fibers. The composites were tested for their mechanical, physical and Environmental properties. Moreover, the matrix-fiber interaction was studied using scanning electron microscope images (SEM) imaging. This study demonstrates a novel combination of bio-waste reinforcements that not only enhances composite performance but also meets the durability and environmental demands of real-world skateboard applications. Of all the samples, Sample 5 (75% epoxy, 5% calcined eggshell powder, 20% millet stalk fibers) was identified for maximum performance with strongest being the most durable, moisture resistant composite. Furthermore, SEM analysis showed strong fiber-matrix bonding. This clearly highlights the use of local wastes in composites without compromising performance for practical application.
The utilization of natural materials-based composites has recently increased due to their outstanding properties such as low density, low cost, moderately good
This article focused on the effect of natural materials on the Mechanical and Physical Properties of Polymer nanocomposite. Fibers and powder underwent treated with an alkaline solution to improve interfacial adhesion. were constructed with the hand lay-up technique with a PMMA/Epoxy blend and natural powders of egg shells and cuttle bone as reinforcements for medical applications in prosthetic arm fabrication. Therefore the cost of raw materials chosen must be important (i.e. economical and cheap for low-income amputees). Consequently, a prosthesis should be comfortable to wear, simple to put on and take off, light weight, long - lasting, and pleasing to the eye in terms of appearance. The polymer mix composition consisted of 25% PMMA and 75% epoxy, together with three distinct concentrations of natural powders (1, 2, and 3 wt.%) relative to the overall composite weight. The cured resin specimen was evaluated for mechanical and physical parameters, including impact strength, flexural strength, hardness, and density. The results demonstrated that the polymer nanocomposite sample achieved peak impact strength values of 12.2 KJ/m² for cuttle bone and 19.48 KJ/m² for eggshell. The flexural strength recorded was 73 MPa for cuttle bone and 71.2 MPa for eggshell, while hardness values were 83.6 for cuttle bone and 83.8 for eggshell at a 3% nanocomposite ratio. Conversely, the other tests of polymer blends (PMMA + Epoxy) using natural fibers (Siwak and flax) attained the highest results. The impact strength of specimens reinforced with siwak fibers significantly exceeds that of specimens reinforced with flax fibers, with flexural strength and hardness of 13.45 KJ/m², 70.6 MPa, and 86.5 shore D, respectively, compared to the base material (PMMA+EP). The density test results demonstrated an elevation in density corresponding to the increasing weight fraction of nanoparticles (eggshell and cuttle bone) in relation to the base material (PMMA+EP). Therefore, these samples may be considered suitable candidates for use as matrix materials that meet the requirements for prosthetic manufacture.