Metal-insulation (MI) REBCO high-temperature superconducting (HTS) magnet has the advantages of short charging delay, low contact losses, and self-protection abilities, which shows important application prospects in many fields. Recently, Institute of Electrical Engineering, Chinese Academy of Sciences developed a prototype on-board MI HTS coil used for electrodynamic suspension (EDS) system working with an acceleration of beyond 8 g. To design a reliable engineering on-board magnet, specific Ic angle dependence data of short sample under different fields were fully considered to estimate the operating margin and losses accurately of the on-board magnet. A semi-analytical method, combination of the dynamic circuit method and finite element method, was used to analyze the dynamic electromagnetic force distribution inside the on-board magnet under motion state, in which the effect of the propulsion coils and the figure-eight-shaped coils were taken into considerations. Finally, a full-size MI double pancake racetrack coil was fabricated and tested in a liquid nitrogen bath. The test results meet the design requirements and verify the feasibility of the design, which provides an important reference for the experiment of on-board EDS with high acceleration in the future.
29 November 2010 in IEEE Transactions on Applied Superconductivity
A superconducting magnet with the center field of 9.4 T is designed and fabricated for 400 MHz Nuclear Magnetic Resonance. Superconducting coil with NbTi/Cu superconducting wire is employed and cooled by re-condensed liquid helium and the magnet system with the clear-bore of 54 mm. The pulsed tube refrigerator with separated valve is employed to cool the magnet system. The superconducting magnet has an active shield with high pure copper shield to protect during quench of the shielding coil. The paper reports the electromagnetic design, and fabrication is detailed.
22 March 2022 in IEEE Transactions on Plasma Science
To investigate the erosion phenomenon of solid armature in the sliding electrical contact process, a 2-D numerical model of melt-wave erosion (MWE) based on the finite element method was established in this article. In this model, the magnetic field excitation boundary expands along the erosion direction into a new magnetic field excitation area. And this model was compared with four previous models under the same conditions, and the comparison results show good consistency. In addition, the temperature dependence of conductivity was considered to investigate its effect on MWE. It is found that the erosion velocity is faster and the penetration depth of the magnetic field in the material is greater when the conductivity changes with temperature. Moreover, the peak current density on the armature symmetry line transfers the tail to the lead. For the case of applying pulse current excitation, the melt erosion distance of the armature tends to be gentle with time. And the time ratio and amplitude of input current have a significant influence on the final erosion distance. The results of these investigations will help further understand the onset of the transition.
The armature is driven forward by induced electromagnetic force in asynchronous induction coil launcher, and the space–time characteristics of force on the armature affect the exit velocity and energy conversion efficiency. Affected by the driving current, velocity, displacement, and other factors, the electromagnetic force received by the armature has obvious nonlinear characteristics. In this article, simulation and analysis of the electromagnetic volume force (EVF) distribution of the armature under different initial positions in the transient model using the field-circuit coupling theory and finite element method are studied. The characteristics of the armature force during the propulsion process are summarized. The structure of armature is optimized according to the simulation results and experiments. It is found that depending on the initial position, the electromagnetic force distribution also varies. There is an optimal initial position that allows the armature to greatly reduce the value of peak force under the premise of ensuring exit velocity. During the period of propulsion, there are two concentrated areas of EVF on the armature. Because of the three-phase excitation, there are three peaks in each of the two areas. The distance between the peaks is about the width of single driving coil, which can be used to optimize the structure of armature.
7 January 2019 in IEEE Transactions on Applied Superconductivity
Rare earth barium copper oxide (REBCO)-type materials are widely used in second-generation high-temperature superconductor tapes to carry high current volumes. These tapes can provide high critical currents along with good tolerance to perpendicular magnetic fields. However, REBCO tapes generally use a laminate structure that suffers from low peeling strength among its inner interfaces. Previously, we proposed a bending-peeling (BP) method and applied it to measurement of the interfacial strength of REBCO tapes at room temperature. All samples failed at the REBCO layer at room temperature. In this work, we used the BP method to perform low-temperature interfacial strength measurements at liquid-nitrogen temperatures. There are two types of failure, where one involves peeling of the REBCO layer and the other involves peeling at the interface between the tape and the epoxy resin. The errors in the BP method were discussed in detail. The superconducting current was monitored during the BP experiment and showed that the effect of out-of-plane tensile stress on the superconducting current was not significant before the breaking of the tape. The degradation in the superconductivity is mainly caused by the structural failure of the REBCO layer.