Composite materials that consisted of a polymer resin as matrix (PMCs), filled using construction and demolition (C&D) wastes powder of different grain sizing in micro-scale were manufactured and studied. Three different kinds of resins were used as the matrix for the purposes of this study. More specifically, composites made of epoxy and unsaturated polyester resins purchased from the market and phenolic resin (novolac) laboratory synthesized, were produced. The morphological and elemental analysis of these materials was performed through scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Additionally, mechanical performance and thermal insulating efficiency of these materials were examined through bending and shear strength tests according to the three-point method and via determination of the thermal conductivity coefficient λ. C&D wastes have undergone the appropriate processing in order to prepare filling products of the required granular size in pulverized form. In this research study, construction and demolition waste-based thermosetting polymer composites were produced with flexural strength in the range 20–60 MPa, shear strength in between 1–8 MPa, and thermal conductivity coefficients in the range of 0.27–1.20 W/mK. The developed materials embedded 30–50% w/w C&D wastes, depending on the resin used as the matrix.
The development of composite materials filled using Construction and Demolition wastes (CDW), characterised by descent mechanical and thermo-insulating properties has been investigated experimentally in this paper. Composites of epoxy resin containing CDW of different grain size and w/w concentrations as additives were manufactured. Additives used, have been prepared through appropriate processing. Our investigations indicated that flexural and shear properties of composites encapsulating 300 μm additives at 30% w/w have been improved, compared to all other composites examined (i.e. composites loaded with 300 μm additives at 40% and 50% (w/w), 500 μm loaded composites at 30%, 40, and 50% w/w), taking a value of 60.03 MPa for flexural strength and 7.54 MPa for shear strength respectively, characterizing them as optimum, in terms of mechanical performance. Next, the thermal insulation capacity study for these materials has been then carried out. Thermo-insulating efficiency of composites has been evaluated by determination of thermal conductivity coefficient (λ), which has been calculated at 1.02 W m-1 K-1, exhibiting good insulation performance, compared to conventional building and insulation materials. The feature of these materials to demonstrate combined adequate mechanical and thermal insulation properties, confirms their appropriateness to be utilised as building and insulation materials.
This research investigates the potential of manufacturing composite materials combining good mechanical and thermal insulation characteristics using C&D wastes (Construction and Demolition waste) in substitution of raw aggregates. Unsaturated polyester matrix composites encapsulating C&D waste of 300 μm and 500 μm as additives, at concentrations of 30%, 40% and 50 (% w/w) respectively, were manufactured. The effects of loading these materials with C&D wastes, in terms of mechanical and thermo-insulating performance were studied. Experimental research revealed the strong interrelation between the mechanical performance of materials and parameters such as grain size and concentration of loading agent. In particular, composites encapsulating 300 μm additives demonstrated improved flexural and shear properties, taking values of 34.59 MPa (30% additives), 35.61 MPa (40% additives) and 30.25 MPa (50% additives) for flexural strength and 3.72 MPa (30% additives), 4.18 MPa (40% additives) and 2.66 MPa (50% additives) for shear strength, compared to corresponding 500 μm loaded composites which flexural strength reached 33.58 MPa (30% additives), 34.6 MPa (40% additives) and 27.47 MPa (50% additives). Similarly shear strength reached 2.81 MPa (30% additives), 3.87 MPa (40% additives) and 2.5 MPa (50% additives) respectively. Composite materials loaded at a concentration of 40% (w/w) using 300 μm C&D waste additives, exhibited optimal mechanical efficiency in terms of flexural and shear strength. Thermo-insulating properties of optimum, in terms of mechanical behavior, composite materials were afterwards investigated. Thermal insulation efficiency was determined by measurement of thermal conductivity coefficient (λ) which was calculated at 0.039 W m-1 K-1, lying within the range of values referred in literature for common insulation materials (0.035-0.16 W m-1 K-1). In conclusion, the characteristic attribute of these materials to exhibit adequate mechanical and thermal insulation properties, as validated by the experimental results, indicates their suitability as building and insulation materials in construction applications.
A comparative economic and life cycle based analysis of five management scenarios for the solid waste generated in the island of Syros was conducted. The LCA part was performed with the LCA – IWM software. The four on-site waste management scenarios were: i) source separation of recyclable materials in combination with landfill disposal of the residuals (existing situation), ii) aerobic, windrow type, biological treatment (composting) with landfilling of residues, iii) anaerobic biological treatment (digestion) with landfilling of residues iv) aerobic mechanical biological treatment (MBT) and landfilling of residues. The off-site management scenario examined the transportation of the whole commingled wastes off the island for processing and disposal to the main mechanical and biological pretreatment plant in Athens. The results of analysis showed that the optimum waste management scenario in terms of environmental burdens (based on six environmental impact categories) and economics was off-site transportation, even when the specific landfill tax is included in calculations. The second best scenario in terms of environmental performance included the on-site aerobic MBT plant while the worst scenario was direct landfilling with mixed dry recyclables’ recycling. On-site anaerobic digestion had less environmental burdens and was more expensive than open windrow composting. Threshold distances were calculated below which the transportation of municipal solid wastes from a small island is financially and environmentally beneficial.