Electrode deformation can cause high local strain and serious capacity degradation in lithium-ion batteries (LIBs) during cycling. Risk reduction in many applications requires an understanding of the effects of the charging/discharging rate on the electrode structure during the battery life cycle. Cyclic charging/discharging experiments of wound 18 650 cylindrical LIBs were conducted at different charging/discharging rates (1C and 2C) to determine the effect of rate on electrode deformation. The charging/discharging capacity as well as battery voltage and time were analyzed during cycling. To acquire electrode deformation images and meet the requirements of computed tomography (CT) within 2 min during the charging/discharging process, sparse-view CT was performed at fixed cycle intervals. Subsequently, a sparse-view reconstruction network was proposed to generate a slice image. Finally, the electrode displacement and strain fields were calculated using the augmented Lagrangian digital image correlation algorithm. The causes of electrode deformation were analyzed and discussed from the perspective of molecular and macroscopic structure. Experimental results show that the structural similarity, peak signal-to-noise ratio and root mean square error in the reconstructed image of the axial section within the battery obtained via the proposed network were 0.9616, 38.7411 dB and 0.0108, respectively, which were better than the other methods of comparison. After 100 cycles, the capacity decay of the battery at 2C was 9.23-fold higher than that at 1C. After 100 cycles at 2C, the maximum displacement of the electrode reached 0.46 mm along the x-direction. The electrode structural deformation of the battery can be intuitively understood at different rates, which facilitates reasonable utilization and structural optimization of the battery.
4 January 2021 in The International Journal of Advanced Manufacturing Technology
X-ray computed tomography (CT) is a widely popular non-destructive testing (NDT) technology for engineering, which also plays an important role in the NDT testing for radial tires. The steel wires in radial tires are densely arranged and regularly distributed, which usually need high-energy X-rays to penetrate completely. Due to the limitation of tire size and mechanical structure, it is sometimes impossible to scan full-360-degree. In this paper, a scheme of alternating short-scan tomography for circumferential slices on one side of the tire is proposed, and a set of special X-ray NDT instrumentation for radial tires is developed. This solution solves the problem of transilluminating the entire tire in traditional CT scans, and can effectively reduce the maximum penetration energy and radiation dose. Furthermore, the winding problem of high voltage cable and oil cooling service pipeline in the process of rotation is well avoided. Then, a short-scan CT reconstruction method with the offset rotation center is deduced, which can effectively eliminate the image artifacts caused by the connection line between the rotating center of the turntable and the focus of the ray source is not perpendicular to the imaging plane of the detector. Computer simulations and experimental results prove the correctness of the proposed compensation symmetry filling reconstruction algorithm. The proposed method can effectively improve the reconstruction accuracy and suppress the reconstruction artifacts. Based on this, the requirements of mechanical assembly precision can be relaxed, which has a certain engineering significance.
In X-ray industrial computed tomography (ICT) imaging, beam hardening artifacts significantly degrade the quality of reconstructed images, leading to cupping effects, ring artifacts, and reduced contrast resolution. These issues are particularly severe in high-density and irregularly shaped aerospace components, where accurate defect detection is critical. To mitigate beam hardening artifacts, this paper proposes a correction method based on the VGG16 feature extraction network. Continuous convolutional layers automatically extract relevant features of beam hardening artifacts, establish a nonlinear mapping between artifact-affected and artifact-free images, and progressively enhance the model’s ability to understand and represent complex image features through stacked layers. Then, a dataset of ICT images with beam hardening artifacts is constructed, and VGG16 is employed to extract deep features from both artifact-affected and reference images. By incorporating perceptual loss into a convolutional neural network and optimizing through iterative training, the proposed method effectively suppresses cupping artifacts and reduces edge blurring. Experimental results demonstrated that the method significantly enhanced image contrast, reduced image noise, and restored structural details, thereby improving the reliability of ICT imaging for aerospace applications.
26 April 2024 in Journal of Nondestructive Evaluation