The current problem of contamination caused by colored industrial effluents has led to the development of different techniques to remove these species from water. One of them, polymer-enhanced ultrafiltration (PEUF), has been systematically studied in this mini review, in which research works from 1971 to date were found and analyzed. Dye retention rates of up to 99% were obtained in several cases. In addition, a brief discussion of different parameters, such as pH, interfering salts, type of polymer, dye concentration, and membrane type, and their influence in dye removal is presented. It was concluded from the above that these factors can be adapted depending on the pollutant to be remediated, in order to optimize the process. Finally, theoretical approaches have been used to understand the intermolecular interactions, and development of the studied technique. In this revision, it is possible to observe that molecular docking, molecular dynamics simulations, density functional theory calculations, and hybrid neural-genetic algorithms based on an evolutionary approach are the most usual approximations used for this purpose. Herein, there is a detailed discussion about what was carried out in order to contribute to the research development of this important science field.

Bio-based hydrogels that adsorb contaminant dyes, such as methyl orange (MO), were synthesized and characterized in this study. The synthesis of poly([2-(acryloyloxy)ethyl] trimethylammonium chloride) and poly(ClAETA) hydrogels containing cellulose nanofibrillated (CNF) was carried out by free-radical polymerization based on a factorial experimental design. The hydrogels were characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy, and thermogravimetry. Adsorption studies of MO were performed, varying time, pH, CNF concentration, initial dye concentration and reuse cycles, determining that when the hydrogels were reinforced with CNF, the dye removal values reached approximately 96%, and that the material was stable when the maximum swelling capacity was attained. The maximum amount of MO retained per gram of hydrogel (q = mg MO g⁻¹) was 1379.0 mg g⁻¹ for the hydrogel containing 1% (w w⁻¹) CNF. Furthermore, it was found that the absorption capacity of MO dye can be improved when the medium pH tends to be neutral (pH = 7.64). The obtained hydrogels can be applicable for the treatment of water containing anionic dyes.

The main objective of this work was to study the release of cinnamaldehyde (CIN) from electrospun poly lactic acid (e-PLA) mats obtained through two techniques: (i) direct incorporation of active compound during the electrospinning process (e-PLA-CIN); and (ii) supercritical carbon dioxide (scCO₂) impregnation of CIN within electrospun PLA mats (e-PLA/CIN_imp). The development and characterization of both of these active electrospun mats were investigated with the main purpose of modifying the release kinetic of this active compound. Morphological, structural, and thermal properties of these materials were also studied, and control mats e-PLA and e- ${\mathrm{PLA}}_{{\mathrm{CO}}_2}$ were developed in order to understand the effect of electrospinning and scCO₂ impregnation, respectively, on PLA properties. Both strategies of incorporation of this active compound into PLA matrix resulted in different morphologies that influenced chemical and physical properties of these composites and in different release kinetics of CIN. The electrospinning and scCO₂ impregnation processes and the presence of CIN altered PLA thermal and structural properties when compared to an extruded PLA material. The incorporation of CIN through scCO₂ impregnation resulted in higher release rate and lower diffusion coefficients when compared to active electrospun mats with CIN incorporated during the electrospinning process.

In this work, electrospun fibers of polyvinyl alcohol (PV) and starch (ST) were obtained to improve dispersion of cellulose nanocrystals (CNC) within a poly(lactic acid) (PLA) matrix with the aim of enhancing mechanical and barrier properties. The development and characterization of electrospun fibers with and without CNC, followed by their incorporation in PLA at three concentrations (0.5%, 1% and 3% with respect to CNC) were investigated. Morphological, structural, thermal, mechanical and barrier properties of these nanocomposites were studied. The purpose of this study was not only to compare the properties of PLA nanocomposites with CNC embedded into electrospun fibers and nanocomposites with freeze-dried CNC, but also to study the effect of electrospinning process and the incorporation of CNC on the PV and starch properties. SEM micrographs confirmed the homogenous dispersion of fibers through PLA matrix. X-ray analysis revealed that the electrospinning process decreased the crystallinity of PV and starch. The presence of CNC enhanced the thermal stability of electrospun fibers. Electrospun fibers showed an interesting nucleating effect since crystallinity of PLA was strongly increased. Nanocomposites with electrospun fibers containing CNC presented slightly higher flexibility and ductility without decreasing barrier properties.