The hyperbolic function proposed by Abbo–Sloan was employed not only to approach the Mohr–Coulomb criterion but also to express the plastic potential function. A better approximation to the Mohr–Coulomb yield and potential surfaces was achieved by increasing the transition angle and proven to be highly efficient in numerical convergence. When a Gaussian integral point goes into plastic state, two cases on yield stress adjustments were introduced. They may avoid solving the second derivative of the plastic potential function and the inverse matrix compared with the existing subroutine. Based on the above approaches, a fully implicit backward Euler integral regression algorithm was adopted. The two- and three-dimensional user subroutines which can consider the associated or non-associated flow rule were developed on the platform of the finite element program—ABAQUS. To verify the reliability of these two subroutines, firstly, the numerical simulations of the indoor conventional triaxial compression and uniaxial tensile tests were performed, and their results were compared with those of the embedded Mohr–Coulomb model and the analytical approach. Then the main influential factors including the associated or non-associated flow rule, the judgment criteria of slope failure, and the tensile strength of soil were analyzed, and the application of the two-dimensional subroutine in the stability analysis of a typical soil slope was discussed in detail through comparisons with the embedded model and the limit analysis method, which shows that this subroutine is more applicable and reliable than the latter two.
Wind energy is one of the most sustainable and renewable resources for power generation. Offshore wind turbines (OWTs) derive significant wind energy compared to onshore installations. One of the greatest challenges encountered by installing the OWTs is the adequate design of their foundation in relatively soft and compressible marine soil. In most cases, the OWTs are supported by a single pile, termed as ‘monopile foundation’. Apart from the usual loads from the superstructure, these piles are subjected to complex loading conditions under static and cyclic modes in the axial, lateral, and torsional directions due to the primary actions of the wave, wind, and current. To incorporate an appropriate design methodology, understanding the failure mechanisms of such piles is of the utmost necessity. This review paper aims to focus on the progressive development in the analysis of failure mechanisms and design practice relevant to the monopile foundations for OWTs by theoretical and experimental studies conducted globally. An extensive literature survey has been carried out to study the gradual progress on offshore pile-soil interaction, failure mechanisms, and design techniques of OWT supporting monopile foundations. Based on the studies, a brief overview of the various aspects of analysis and design has been carried out, and the relevant conclusions are drawn therefrom.
1 October 2016 in International Journal of Geomechanics
This paper presents a new earth-retaining structure, the moso bamboo soil-nailed wall. Moso bamboo (including branches) is employed as soil nails and piles, and used to weave bamboo strip grids (replacing rebar grids) for sprayed-concrete surface courses. In this paper, the design and construction methods of this structure are elaborated using laboratory and field tests, and numerical simulations for two completed projects with respect to stability and deformation, respectively. In-situ tests show that the pulling capacity of bamboo nails (with branches) increased by ∼2.5–2.8 times in stiff soil or soft clay, respectively, compared with steel-pipe nails. For one wall in soft clay, numerical analysis was conducted, which verified the stability of the bamboo-reinforced system (compared with the soil-nailed wall constructed with steel-pipe nails, which failed). For another wall, the deformation and internal force of the structure were obtained using three-dimensional (3D) nonlinear numerical software...
1 October 2018 in International Journal of Geomechanics
The representation of the Hoek-Brown criterion is an irregular curved hexagonal pyramid in the principal stress space, which leads to the occurrence of numerical singularities on the edges of the pyramid. With the aim of achieving a physical approximation to the pyramid, this study used both the C1 and C2 smoothing artifices on its sharp edges, and it was found that they were able to successfully eliminate the singularity and ensure the convexity of the yield surface. Meanwhile, to reflect the characteristic of the poor tensile strength of a rock mass, a tension cutoff surface was employed to form the whole modified combined yield surface. To facilitate comprehension and programming, the initial Hoek-Brown criterion and the smoothing and tension cutoff yield functions were all expressed in terms of stress invariants. The fully implicit backward Euler integral regression algorithm was employed to form the consistent stiffness matrix to ensure the high accuracy and fast convergence of numerical computations. In accordance with the failure zone in which a trial stress may fall, it may be pulled back to the initial Hoek–Brown yield surface, the transitional rounding yield surface, the tension cutoff yield surface, or the vertices that are the intersections of the former two with the latter. Furthermore, to facilitate the application of this modified Hoek-Brown criterion, a three-dimensional (3D) user-defined material behavior subroutine was developed in a finite-element program, and its reliability and applicability were verified through the numerical simulations of the triaxial compression and uniaxial tension tests of a rock and the excavation of a rock tunnel.
In this study, combined with an engineering case, nonlinear finite element (FE) analysis is adopted to explore the mechanism of a deep soft soil foundation pit supported by bamboo soil nails and bamboo piles in rows. Firstly, a plain strain model is built to analyze the stability of the pit excavated with a slope with 45° inclination angle and without a retaining system. It reveals that its factor of safety is so small that effective retaining measures should be taken. In order to reasonably analyze the working mechanism of this particular retaining structure, a high-fidelity simulation is carried out in the Super Computing Center of Fujian Province using three-dimensional (3-D) FE methods. That is to say, bamboo soil nails are modeled with solid elements instead of structural elements. In addition, the dense bamboo piles in rows are modeled with the equivalent diaphragm wall. Coulomb's frictions between the soils and bamboos, as well as soils and diaphragm wall, are considered. Mohr-Coulomb's constitutive model and strength reduction finite element technique are employed in the numerical analysis. In order to decrease the computational costs, displacement constraint and its release method are adopted to simulate the process before and after excavation. The study shows that an appropriate stability and structure analysis method for foundation pits supported by this kind of structure is presented. The research outcomes will facilitate this sort of environment-friendly, energy-saving and cost-saving retaining structure to be widely used in excavation engineering.