When lightning strikes an aircraft, the electromagnetic (EM) field penetrates inside the aircraft, and induces currents and voltages on the onboard cables, resulting in the risk of equipment failure, which is a serious safety hazard to the flight safety. With the wide use of low-conductivity composite materials in aircraft manufacturing, the EM shielding effectiveness of the aircraft is weakened. As for the helicopter, the proportion of windows and doors is relatively larger than the fixed-wing aircraft, thus the EM shielding effectiveness is much weaker. Proper lightning protection design must be validated to eliminate the risk of electrical and electronic equipment failure. This paper describes the lightning indirect effects related to the modeling and simulation process of the composite UH-60 helicopter. The external and internal EM field environment together with the induced currents and voltages on cables are discussed. Moreover, in order to validate the simulation, an iron helicopter model was tested and the comparison between simulated and measured waveforms was carried out.
20 January 2023 in IEEE Transactions on Plasma Science
With the wide application of unmanned aerial vehicles (UAVs), more attention has been paid to the safe operation of UAVs in complex electromagnetic environments. In this article, we investigate the impact of high-power microwave (HPM) pulses on three types of typical commercial UAVs. We established the HPM irradiation experiment system first and obtained the responses of UAVs under the HPM attack with different electric field strengths. The flight logs and the damage analysis reports indicate that the damaged components of the type I UAV and the type II UAV are the rotor motor and the electronic speed controller. The experiment results prove that L-band narrowband HPM microwave has strong backdoor coupling effects on UAVs. The damage mechanism of UAVs by the HPM is studied by simulation. The simulation results show that an HPM pulse will cause a high-voltage pulse coupled to the cable connecting the electronic speed controller and the rotor motor, which caused the electronic speed controller to send out a false signal that caused the rotor motor speed to rise sharply, eventually making the rotor motor to burn out. Experiment results show that strengthening electromagnetic protection on the cable can effectively prevent HPM damage to UAVs. The simulation results match the experiment results and the damage analysis reports. Finally, some suggestions are provided to improve the UAV’s anti-HPM capability.
5 June 2023 in IEEE Transactions on Electron Devices
Nanosecond square voltage pulse is of wide interest because of its potential military and industrial applications, such as high-power microwave (HPM). In this article, a gigawatt pulsed power generator (PPG) for HPM based on the multistage pulse forming networks (PFNs) with a voltage superposition using the Marx scheme, i.e., PFN-Marx generator, is proposed through the theory analysis, numerical simulation, processing manufacturing, and performance experiment. The PPG consists of the main subsystems of the primary power and pulse modulation subsystems. The primary power subsystem is a modular bipolar dc high-voltage generator based on the ac–dc–ac, high-frequency transformer, and voltage multipliers by using the power electronics switches. It can generate bipolar dc high voltage of ±42 kV to charge the PFN-Marx generator. As for the pulse modulation subsystem, the PFN-Marx technique is preferred, which consists of 24-stage and six ${L}$ - ${C}$ sections. To verify the PPG, an experimental prototype is fabricated and tested. It has a characteristic impedance of about $40~\boldsymbol \Omega $ and can deliver square voltage wave with an output voltage pulse of about 500 kV, full-width at half-maximum (FWHM) of 94 ns, and 10%–90% rise time of fewer than 35 ns, indicating its ability to deliver peak power beyond 6.25 GW. In addition, a transit-time oscillator was connected and can radiate microwave power of 0.8 GW at 12.89 GHz for the cathode voltage of 372 kV and the beam current of 9.3 kA.
19 October 2020 in IEEE Transactions on Plasma Science
The gyromagnetic nonlinear transmission line (GNLTL) is a compact and solid-state high-power microwave source, which can be treated as a special coaxial transmission line partially filled with the ferrite material. Due to the complex interaction process of the electromagnetic fields with the dynamic damped precessional motion of the magnetization vector in the ferrite, it is of great challenge to theoretically predict the output of the GNLTL. Here, we present a novel field-line coupling simulation method to predict the output waveform of the GNLTL by simultaneously solving the coupled system of the Landau–Lifshitz–Gilbert equation and Maxwell’s equations in the 2-D cylindrical coordinate system. In particular, the simulation model is validated by comparing the computation results with the experimental results obtained by Bragg et al. in the HPM experiment. The influences of the GNLTL length and bias magnetic field are analyzed. The proposed computation method can provide a solution for improving the performance of the GNLTL.
10 November 2023 in IEEE Transactions on Plasma Science
Aiming at the damaging effect of high-power microwave (HPM) on the limiter-protected low-noise amplifier (LNA), both of the HPM irradiation experiment platform and TCAD simulation are built. It shows that with the increase of the injection power, a plateau leakage power is observed. The excessive leakage power will damage the LNA. Moreover, the experimental results show that the damage threshold decreases with the increase of the pulsewidth or the pulse number. In addition, the pulse repetition frequency has little influence on the damage threshold of the limiter-protected LNA. The damage mechanism and damage location of the limiter-protected LNA are simulated. The simulation results are consistent with the experimental results. The study is of great significance in evaluating the protective ability of PIN limiters against LNAs with the HPM.
2 February 2023 in IEEE Transactions on Plasma Science
This study aims at studying the damage effect of gallium arsenide (GaAs) heterojunction bipolar transistor (HBT) low noise amplifier (LNA) with repetitive high-power microwave (HPM) pulses. The theoretical function for the thermal accumulation effect is derived, which depends on the pulsewidth, the pulse repetition frequency (PRF), and the input power. A simulation model is established to investigate the thermal accumulation effect of repetitive HPM pulses on the HBT. The electric field, current density, and temperature distributions in the HBT with repetitive HPM pulses are discussed first. The influence of the repetitive HPM pulse parameters on the thermal accumulation effect is studied by theoretical analyses and simulations. Results show that the thermal recovery time increases with the pulsewidth or the input power increases. In addition, it is concluded that the frequency does not affect the thermal recovery time. The simulation results agree with the theoretical results. Finally, the damage effect of repetitive HPM pulses is experimentally verified.