The cutting variables of end milling are positively correlated with the machined surface roughness, but their mechanism of action remains unclear. Since the cutting tool used in end milling is a three-dimensional solid, under the action of horizontal cutting force, there exist both axial tensile strain and axial compressive strain in the cutting tool at the same time, thus putting forward an assumption about the formation mechanism of machined surface roughness: cutting variables affect the axial tensile strain of the cutting edge through the horizontal cutting force, and cause the cutting-edge tip to vertically wedge into the machined surface, thereby influencing the unevenness of the processed surface. Based on the cutting-tool deflection model of a two-segment cantilever beam and the horizontal cutting force formula, the mathematical expression for the axial strain at the sharp tip of the cutting edge was derived. Groove milling and half-groove milling experiments were done, and the experimental results show that the roughness Ra value in the central area is significantly higher than that in the cut-in area, with its maximum average value being 1.32 times that of the cut-in area. The surface roughness rises following the rise in depth of machining and feed per cutting tooth, but this relationship is significant. The laboratory findings are consistent with the theoretical analysis results, indicating that the assumption about the formation mechanism of surface roughness should be reasonable, and the surface roughness in the central area is greater than that in the cutting tool cut-in area. The research results provide a kind of new insight into the formation mechanism of machined surface roughness, which can serve as a reference for relevant research and cutting practices.
The measured standard resistance at 20 °C () is a critical indicator for evaluating the quality of electric cables. Utilizing a thermal circuit model allows for the rapid determination of . Focusing on civil electrical cables, this study constructs a thermal circuit model based on an equivalent circuit. Through mathematical derivation, model parameters are expressed as functions of the insulation cross-sectional area and conductor specification. Subsequently, the insulation area is fitted to the conductor specification, establishing a universal analytical thermal circuit model with the conductor specification as the sole variable. Ambient temperatures measured under specific operating conditions showed exponential variation. Using corresponding simulated conductor temperatures, the Differential Evolution algorithm was employed to train the model, achieving a training standard deviation of 0.0184 °C. Validation under different conditions demonstrated that for various cable specifications, the conductor temperature prediction deviation within 300 s remained within 0.368 °C, and the maximum estimation error for was less than 0.148%. These results indicate that the established model possesses high calculation accuracy and strong universality, offering a valuable tool for researchers and practitioners in fields relevant to civil electrical cables.
Burrs are a significant machining defect affecting the quality of precision parts, and tool eccentricity may substantially influence milling burrs. Using AISI 304 stainless steel as the workpiece material, a three-dimensional thermo-mechanical coupled model for slot milling was constructed based on an explicit dynamics model. Combining the Johnson–Cook (J-C) constitutive model with the J-C shear failure criterion, simulations were conducted to obtain burr dimensions, cutting temperature distributions, and cutting force waveforms under different tool eccentricity directions and magnitudes. Results: As the eccentricity increases, the temperature of the top burr rises, and both the width of the top burr and the thickness of the exit side burr significantly increase. Under simulated conditions, the width of the top burr in down milling side increased by up to 70%. The burr dimensions under different eccentricity directions can differ by approximately 40%. Groove milling experiments revealed similar burr shapes between experimental and simulated results. Furthermore, the simulated cutting force waveforms aligned with those in the literature, indicating the reliability of the simulation outcomes. Based on these findings, it can be concluded that tool eccentricity significantly affects the dimensions of top burrs and exit side burrs. The width of top burrs and the thickness of exit side burrs are positively correlated with the tool eccentricity distance, while exit bottom burrs remain unaffected by eccentricity. These research results provide valuable reference for burr suppression in practical machining operations.
13 December 2018 in IOP Conference Series: Materials Science and Engineering
The finite element model of the linear motor machine tool was established by the finite element software, and the multi-field coupling analysis and modal analysis of the linear motor for the machine tool were carried out. The deformation amount of the machine tool driven by linear motor under multi-field coupling was obtained. At the same time, the force cloud diagram, the first 6th modal analysis of the important components (machine base), the natural frequency and vibration mode of the base are all obtained. The result shows that the natural frequency is much lower than the excitation frequency, so it can effectively avoid the resonance phenomenon. This article can provide reference for the application of linear motor on machine tools.