Wireless communication is prone to collisions, resulting from multiple devices transmitting at the same time. It implies subsequent retransmissions, which increase energy consumption of communicating devices and reduce throughput of the network. This is especially critical in Internet of Things (IoT) networks, in which the number of connected devices grows rapidly and the available energy of IoT end devices is rather limited (e.g., energy harvesting and battery powered). The number of retransmissions must be reduced in order the networks to be sustainable. However, in long-range wireless IoT networks, the most effective collision-resolution techniques using a transmission-channel listening to detect collisions cannot be reliably used due to various problems, such as a hidden-node problem or environment interference. In this article, a new solution of this problem is proposed, which consists of a new communication-planning mechanism for low-speed long-range IoT networks with a huge number of communicating energy-constrained devices. The access points (APs) (or IoT gateways) are used to plan the periodically repeated communication into a transmission schedule, allowing only a single IoT device to communicate at a time. This approach results in reduction of collisions, which leads to the increased network throughput, smaller delays, and lower power requirements of energy-constrained devices. The experiments indicate that the proposed approach provides better communication efficiency than the LoRaWAN and Sigfox collision-resolution techniques, when more than 15, respectively 125, end devices communicate with a single AP.
The era of the Internet of Things comes with a huge number of interconnected communicating devices, which are often rather limited on the energy supply (e.g. battery powered or energy harvesting). Therefore, the pressure on energy efficiency of their operation (influencing lifetime or amount of functions) is especially crucial. In spite of a growing number of IoT devices, there still are many applications that are very specific and their market is quite limited. This is where the FPGAs offer a good alternative to dedicated application-specific chips, which would be too costly for such a purpose. Therefore, we target the powermanagement automation that simplifies energy-efficient design for FPGA platforms. A designer is then able to specify just an abstract power management in the commonly used SystemC model and it is automatically transformed in the more-complex form acceptable by a specific FPGA device. The proposed simplification and automation shortens the time-to-market of energy-efficient IoT products and prevents possible humanerrors that could be otherwise introduced to the design. The alleviated verification and debugging spare even more time in the development process. The experiments have proved the benefits of the proposed automation method.
Number of embedded devices connected to the Internet is rapidly increasing, especially in the era of the Internet of Things (IoT). The growing number of IoT devices communicating wirelessly causes a communication-parameters selection problem, implying the increasing number of communication collisions. Multiple factors of IoT networks signify this problem, such as inability of communication-channel listening prior to the transmission (due to longer distances), energy constrains (due to inability of powering devices from the grid), or limitation of duty cycle and high interference (due to usage of an unlicensed band in communication technologies). This article is focused on alleviating this problem in LoRa networks, which is one of the most promising technologies for long-range and low-power communication. We utilize the existing LoRa@FIIT protocol to achieve ultra energy-efficient communication. In the proposed architecture, the scalability of the LoRa network is increased by modifying the communication-parameters selection algorithm. The original adaptive data rate algorithm is efficient in static environments. However, when considering mobile nodes, upper confidence bound algorithm can provide more energy-efficient communication, as shown in this work. The end nodes are partially independent from the network server, able to modify their communication parameters on their own. The adaptation to network changes is thus faster. Also, by ensuring the quality of service mechanism at each node in the infrastructure, the application domain of the proposed architecture is widened. The simulation-based experimental results showed a significantly reduced number of collisions for mobile nodes, which reduces the channel congestion and the wasted energy by retransmissions.
The rapidly growing segment of the Internet of Things (IoT) makes the security threats more prominent than ever. The research around communication security and cybersecurity in such networks is still a challenge, mainly due to the typically limited energy and computation resources of IoT devices. The strong security mechanisms require significant power and thus the energy wastage must be minimized. Optimized application-specific security protocols are commonly used to make the data transfer more efficient, while still offering a high level of security. The supported security features, such as confidentiality, integrity or authenticity, should not be affected by the optimization. Our work is focused on optimizing one of the existing security protocols for the use in the IoT area, namely the Host Identity Protocol (HIP). Based on the analysis of related works, we have identified multiple possibilities for optimization and combined some of them into the proposed E-HIP optimized protocol. For verification purpose, it has been implemented as a modification of the open-source OpenHIP library and applied on a communication between real hardware devices. The secured communication worked correctly. The resulting effect of the proposed optimization has been evaluated experimentally and it represents an increase in energy efficiency by about 20%. Compared to other HIP optimizations, the achieved results are similar; however, the proposed optimizations are unique and can be further combined with some of the existing ones to achieve even higher efficiency.
With the expansion of the Internet-of-Things, energy-efficient communication is becoming vital. The communication among energy-limited devices (e.g., powered by batteries or harvesting the energy from their environment) must be energy-efficient, prolonging their lifetime or increasing data throughput. This article aims at proposing energy-efficient periodic communication for devices over the ZigBee protocol and powered by a battery. We propose using timing channels for different data priorities, thus, more important data are sent more frequently. The priority is also considered in case of congested traffic, where a central device (coordinator) prioritizes more important communication. We have implemented a simulator, which serves for verification of the proposed solution, and conducted experiments comparing the proposed EEMIP method with the standard nonbeacon ZigBee communication. The experimental results show that the proposed method is more energy efficient.
Power consumption becomes a dominant problem in current hardware-systems design. It is most commonly dealt with use of power-management techniques, such as clock gating, power gating, or voltage and frequency scaling. In modern complex systems, power-management adoption is difficult to achieve, and therefore new approaches to simplify power-managed systems design are evolving. We have also proposed such an approach, simplifying power-management specification at the system level of design abstraction. This paper describes the proposed verification approach, which can take place continuously, beginning at the early specification stage of the system development. It helps a designer to create correct and consistent specification of power management.