Iratxe Maestre

Ms. Iratxe Maestre

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2024 in Sensors
Verified
Journal Article
Open access
PDF file
ISIrati Sanchez
Irati Sanchez
JLJose Luis Lanzagorta
Jose Luis Lanzagorta
IMIratxe Maestre
Iratxe Maestre
Lander GaldosLander Galdos
Lander Galdos
Time-of-Flight Diffraction (TOFD) is a method of ultrasonic testing (UT) that is widely established as a non-destructive technique (NDT) mainly used for the inspection of welds. In contrast to other established UT techniques, TOFD is capable of identifying discontinuities regardless of their orientation. This paper proposes a redesign of the typical TOFD transducers, featuring an innovative curved sole aimed at enhancing their defect detection capabilities. This design is particularly beneficial for thick-walled samples, as it allows for deeper inspections without compromising the resolution near the surface area. During this research, an evaluation consisting in simulations of the ultrasonic beam distribution and experimental tests on a component with artificially manufactured defects at varying depths has been performed to validate the new design. The results demonstrate a 30 to 50% higher beam distribution area as well as an improvement in the signal-to-noise ratio (SNR) resulting in a 24% enhancement in the capability of defect detection compared to the traditional approach.

17 May 2025 in Sensors
Verified
Journal Article
Open access
PDF file
IMIratxe Maestre
Iratxe Maestre
AMAitor De Miguel
Aitor De Miguel
JLJose Luis Lanzagorta
Jose Luis Lanzagorta
ECEwen Carcreff
Ewen Carcreff
Lander GaldosLander Galdos
Lander Galdos
Single-crystal superalloys have attracted considerable interest in aero engine blade manufacture due to their superior mechanical properties, which maintain structural integrity at high temperatures. However, their anisotropic microstructure results in direction-dependent properties that pose a challenge for defect detection. This study proposes a methodology to determine the crystal orientation, which is subsequently used to improve the Total Focusing Method (TFM) by incorporating the refracted beam directivity. Firstly, simulations were performed using semi-analytical models (CIVA software 2023 SP4.1) to reproduce different grain orientations. The results were then post-processed to determine the grain orientation. Finally, the TFM was adapted to take into account not only the velocity variations due to orientation but also the directivity of the ultrasonic beam based only on slowness curves. The implementation of this methodology has improved the defect detection capability, optimizing the defect positioning by up to 61% and increasing the signal-to-noise ratio by up to 5 dB. This study demonstrates the effectiveness of an adapted inspection procedure for single crystals.

1 July 2026 in DYNA Ingenieria e Industria
Verified
Journal Article
Closed access
IMIratxe Maestre
Iratxe Maestre
JLJose Luis Lanzagorta
Jose Luis Lanzagorta
FMFrancisco Pavón Moron
Francisco Pavón Moron
JMJulen Mendikute San Martin
Julen Mendikute San Martin
IDIrati Sanchez Duo
Irati Sanchez Duo
Lander GaldosLander Galdos
Lander Galdos
The inspection of components with complex geometry or microstructure poses a significant challenge, particularly for the detection of volumetric defects. These limitations often necessitate destructive sampling inspections, leading to the generation of defective parts and, in many cases, considerable loss of time and resources. This study presents an innovative non-destructive testing approach that relies on ultrasound imaging techniques (UT-IMAGING). These methods provide clear advantages over conventional ultrasound (UT) techniques, which frequently yield inadequate signals when inspecting intricate components. Such limitations mainly arise because traditional UT systems are not designed for curved surfaces or materials exhibiting anisotropic behavior. UT-IMAGING improves the interpretation of signals generated by advanced ultrasonic transducers. The proposed methodology integrates dedicated simulation models to support inspection design and advanced post-processing algorithms capable of accurately reconstructing the ultrasound images. The approach has been validated through simulation in two industrially relevant scenarios: complex welds in the automotive industry and single-crystal materials with homogeneous anisotropy. The results indicate that UT-IMAGING, enhanced by computational modeling and advanced signal processing, offers a promising pathway and may serve as the basis for future inspection strategies in industries where ensuring component quality is critical. Key Words: Non-Destructive Testing (NDT), Ultrasonic Phased Array (UTPA), Full Matrix Capture (FMC), Total Focusing Method (TFM).

21 April 2026 in Metals
Verified
Journal Article
Open access
PDF file
JLJose Luis Lanzagorta
Jose Luis Lanzagorta
JMJulen Mendikute
Julen Mendikute
ISIrati Sanchez
Irati Sanchez
RVRuiz Vázquez
Ruiz Vázquez
IMIratxe Maestre
Iratxe Maestre
JMJokin Munoa
Jokin Munoa
Ensuring the structural integrity and service reliability of railway wheels has become a key challenge in modern manufacturing and maintenance strategies within the railway sector. In this context, Eddy Current (EC)-based Non-Destructive Testing (NDT) provides an automated and efficient approach for detecting surface and near-surface defects, while reducing inspection time and operator dependency compared to conventional manual methods. This study presents the integration of an EC inspection system into a precision lathe, enabling in-machining evaluation during wheel turning. Experimental validation was conducted on wheels with artificial defects, yielding high signal-to-noise ratios and enabling reliable defect characterization. Furthermore, computationally efficient and easily deployable machine learning algorithms were developed to enable automatic defect detection, localization, and size estimation. The results confirm the feasibility of in-machine EC inspection during machining operations, enabling early defect detection and contributing to safer, more efficient, and higher-quality manufacturing processes in the railway sector.

1 March 2026 in DYNA Ingenieria e Industria
Verified
Journal Article
Closed access
IMIratxe Maestre
Iratxe Maestre
ASAitor DE Miguel Salaberria
Aitor DE Miguel Salaberria
JLJose Luis Lanzagorta
Jose Luis Lanzagorta
Lander GaldosLander Galdos
Lander Galdos
Nowadays, there is not any specific software prepared for the inspection of anisotropic materials in the field of ultrasonic imaging. This current software considers anisotropic materials isotropic, and the results of the inspections are not optimum. Therefore, in this work an algorithm which onsiders the anisotropic character of these materials has been developed. For that purpose, using the CIVA 2023 software for inspections, five different materials with the same defect distribution have been simulated. The results of the algorithm which takes into consideration the anisotropy of the materials have been successful. The improvement on the location of the defects for the anisotropic algorithm has been of 80% on average with respect to the results of classic approaches considering a constant velocity for the material. Due to that, the efficiency and reliability of the developed algorithm opens a path for the growth of different algorithms to improve the quality of the inspections in anisotropic materials.