An oxygen-coordinated cobalt single-atom catalyst was successfully fabricated, exhibiting exceptional electrocatalytic activity toward urea and H2O2 production. Subsequently, the value-added urea peroxide was efficiently synthesized.
Electrocatalytic nitrate reduction reaction has attracted increasing attention due to its goal of low carbon emission and environmental protection. Here, we report an efficient NitRR catalyst composed of single Mn sites with atomically dispersed oxygen (O) coordination on bacterial cellulose-converted graphitic carbon (Mn–O–C). Evidence of the atomically dispersed Mn–(O–C2)4 moieties embedding in the exposed basal plane of carbon surface is confirmed by X-ray absorption spectroscopy. As a result, the as-synthesized Mn–O–C catalyst exhibits superior NitRR activity with an NH3 yield rate (RNH3) of 1476.9 ± 62.6 μg h−1 cm−2 at − 0.7 V (vs. reversible hydrogen electrode, RHE) and a faradaic efficiency (FE) of 89.0 ± 3.8% at − 0.5 V (vs. RHE) under ambient conditions. Further, when evaluated with a practical flow cell, Mn–O–C shows a high RNH3 of 3706.7 ± 552.0 μg h−1 cm−2 at a current density of 100 mA cm−2, 2.5 times of that in the H cell. The in situ FT-IR and Raman spectroscopic studies combined with theoretical calculations indicate that the Mn–(O–C2)4 sites not only effectively inhibit the competitive hydrogen evolution reaction, but also greatly promote the adsorption and activation of nitrate (NO3−), thus boosting both the FE and selectivity of NH3 over Mn–(O–C2)4 sites.
The flower-shaped CuCo 2 O 4 spinel catalyst was used for electrochemical nitrate reduction in an electrolyte. Theoretical calculation shows that NO 3− can be adsorbed on CuCo 2 O 4 to form the *NOH intermediate, so as to obtain a good yield rate and FE.
Electrochemical nitrate reduction reaction (NO3−RR) to synthesize valuable ammonia (NH3) is considered as a green and appealing alternative to enable an artificial nitrogen cycle.
The electrocatalytic nitrate reduction reaction (NitRR) is a promising alternative to the traditional Haber–Bosch process. However, the competitive hydrogen evolution reaction results in poor NH3 selectivity (SNH3). Here, a Cu–Co bimetallic catalyst supported on biomass-derived porous carbon (Cu–Co/BPC) is designed and synthesized. Interestingly, the catalyst presents a high NH3 yield rate of 9114.1 ± 244.8 μg h−1 cm−2 at −1.4 V (vs. RHE) and a high faradaic efficiency (FE) of 84.5 ± 1.6% at −1.0 V (vs. RHE). Notably, the S NH3 of Cu–Co/BPC catalyst is kept above 94.2% under a broad range from −1.0 to −1.4 V (vs. RHE), indicating the high NitRR-to-NH3 selectivity of Cu–Co/BPC. The combination of in situ characterization and experimental results indicates that the electron transfer occurs between Cu and Co, and many active sites are generated for adsorption and activation of NO double bonds, and hydrogenation reactions occur with adjacent H protons to improve the selectivity of NH3.
We demonstrate the fabrication of the large-area arrays of vertically aligned Si/SiO2 nanowires with full tunability of the geometry of the single nanowires by the metal-assisted chemical etching technique and the following thermal oxidation process. To fabricate the geometry controllable Si/SiO2 nanowire (NW) arrays, two critical issues relating with the size control of polystyrene reduction and oxide thickness evolution are investigated. Through analyzing the morphology evolutions of polystyrene particles, we give a quantitative description on the diameter variations of polystyrene particles with the etching time of plasma etching. Based on this, pure Si NW arrays with controllable geometry are generated. Then the oxide dynamic of Si NW is analyzed by the extended Deal-Grove model. By control, the initial Si NWs and the thermal oxidation time, the well-aligned Si/SiO2 composite NW arrays with controllable geometry are obtained.