Activated biochar is a promising porous carbonaceous adsorbent material for organic pollutant removal, but it remains challenging to obtain high porosity and aromaticity through a simple and low-cost synthetic method. The common adsorption mechanisms of organic dyes on activated biochar should be further investigated in order to guide the synthesis of high-efficiency adsorbent materials. Here, we proposed a high-yield (up to 40 wt %) synthetic method of phosphoric acid-activated biochar from pomelo peel (PPC) with a high specific area of 877.3 m2/g through a facile thermal treatment at a relatively low temperature (250 °C). The specific activation mechanism of H3PO4 in the preparation of the adsorbent was investigated by a range of experiments and characterizations. The kinetic and isotherm experiments are also conducted to evaluate its dye adsorption behavior. According to the adsorption experiment results, PPC exhibits high saturated adsorption capacities for methyl orange (MO, 239.1 mg/g), rhodamine B (RhB, 2821.8 mg/g), methylene blue (MB, 580.5 mg/g), and crystal violate (CV, 396.6 mg/g) according to the Langmuir model. The maximum initial concentration of each dye solution for acquiring 90% removal efficiency is estimated to be 234.55 ppm (MO), 2943.8 ppm (RhB), 633.8 ppm (MB), and 423.6 ppm (CV) at 298 K with an adsorbent dosage of 1 g/L. The characterization results also indicate PPC has a complex synergetic mechanism for ionic dye adsorption behavior. This provides perspectives regarding PPC as a promising biochar adsorbent from biomass waste, which is probably useful for high-efficiency dye removal in water treatment.
Phosphoric acid-activated biochar has been proven to be a promising adsorbent for pollutant removal in an aqueous solution. It is urgent to understand how surface adsorption and intra-particle diffusion synergistically contribute to the adsorption kinetic process of dyes. In this work, we prepared a series of PPC adsorbents (PPCs) from red-pulp pomelo peel under different pyrolysis temperatures (150–350 °C), which have a broad specific surface area range from 3.065 m2/g to 1274.577 m2/g. The active sites on the surface of PPCs have shown specific change laws of decreasing hydroxyl groups and increasing phosphate ester groups occurring as the pyrolysis temperature rises. Both reaction models (PFO and PSO models) and diffusion models (intra-particle diffusion models) have been applied to simulate the adsorption experimental data to verify the hypothesis deduced from the Elovich model. PPC-300 exhibits the highest adsorption capacity of MB (423 mg/g) under given conditions. Due to its large quantities of active sites on the external and internal surfaces (1274.577 m2/g), a fast adsorption equilibrium can be achieved within 60 min (with an initial MB concentration of 100 ppm). PPC-300 and PPC-350 also exhibit an intra-particle-diffusion-controlled adsorption kinetic process with a low initial MB concentration (100 ppm) or at the very beginning and final stage of adsorption with a high initial MB concentration (300 ppm) at 40 °C, considering that the diffusion is likely hindered by adsorbate molecules through internal pore channels at the middle stage of adsorption in these cases.
Magnetite nanoparticles (Fe3O4-NPs)/orange peel (MOP) composite was prepared via one-step in-situ co-precipitation method as magnetic heterogeneous Fenton-like catalyst. The properties of MOP were characterized by scanning electron microscopy, transmission electron microscopes, Brunauer–Emmett–Teller, X-ray diffraction, Fourier-transform infrared, thermogravimetric analysis and X-ray photoelectron spectroscopy technologies. Its Fenton-like catalytic responses towards removal of methyl orange (MO) were investigated, in which the effects of initial dye concentration, pH, temperature and hydrogen peroxide dosage were studied. The MO degradation ratio up to 98.0% was obtained within 20 min in optimized conditions. The catalyst showed excellent catalytic stability exhibiting nearly 90% degradation ratio in the 10th cycle within 20 min, whereas pure Fe3O4-NPs showed only 62.5% in this stage. Due to the stabilization of complexing orange peel hydroxyl to iron oxide in the composite and its magnetic separation property, MOP composite exhibits excellent Fenton-like catalytic performance, which offers great prospects for low-cost and high-efficiency organic dye wastewater treatment.
To degrade high-concentration and toxic organic effluents, we developed Fe-Cu active sites loaded on biomass-source carbon aerogel (CA) to produce a low-cost and high-efficiency magnetic Fenton-like catalyst for the catalytic oxidative decomposition of organic pollutants. It exhibits excellent performance in catalytic Fenton-like reactions for RhB removal at an ultrahigh initial concentration of up to 1000 ppm. To be specific, Fe3O4 and Cu nanoparticles are generated in situ on a mesoporous CA support, denoted as an Fe3O4-Cu/CA catalyst. Experimentally, factors including initial dye concentration, catalyst dosage, H2O2 dosage, pH, and temperature, which significantly influence the oxidative degradation rate of RhB, are carefully studied. The RhB (1000 ppm) degradation ratio reaches 93.7% within 60 min under low catalyst and H2O2 dosage. The catalyst also shows slight metal leaching (almost 1.4% of total Fe and 4.0% of total Cu leached after a complete degradation of 25 μmol RhB under conditions of 15 mg catalyst dosage, 20 mL RhB solution (600 ppm), and 200 μL 30 wt% H2O2 dosage, at pH of 2.5, at 40 °C), good catalytic activity for degrading organic pollutants, excellent reusability, and good catalytic stability (the degradation ratio is nearly 82.95% in the 8th cycle reaction). The synergistic effect between Fe and Cu species plays a vital role in promoting the redox cycle of Fe(III)/Fe(II) and enhancing the generation of ·OH. It is suitable for ultrahigh-concentration organic pollutant degradation in practical wastewater treatment applications.
5 January 2024 in ACS Applied Materials & Interfaces
Aquaculture wastewater containing tetracycline hydrochloride (TCH) poses significant environmental problems and health risks. We investigated the adsorption of TCH onto phosphoric acid-activated corncob biochar (PCC) as a sustainable and efficient removal strategy. PCC was synthesized from cob feedstock activated by phosphoric acid under a pyrolysis temperature of 300 °C in a limited-air atmosphere. It was characterized extensively, revealing a high specific surface area (1071.75 m2/g), high porosity with total pore volume of 0.912 cm3/g, and abundant surface functional groups including phosphate, carboxylic, and amine groups. Batch adsorption experiments demonstrated an ultrahigh adsorption capacity for TCH, with a maximum theoretical capacity (Langmuir model) of 953.62 mg/g at 313 K. Its adsorption isotherms transfer from Langmuir type to Freundlich type as temperature rises, indicating a transition from monolayer to multilayer adsorption. The adsorption kinetics were governed by a synergistic mechanism involving surface adsorption and a pore-filling effect (intra-particle diffusion). Critically, the adsorption dynamics exhibit an intra-particle diffusion-controlled process at a low pH (3.0) during the final stage of adsorption. Strong hydrogen bonding led to high initial adsorption rates, and the adsorption converted to diffusion-controlled mode eventually. In contrast, at higher pH (≥7.0), electrostatic repulsion between PCC adsorbents and TCH molecules hindered intra-particle diffusion, causing the final adsorption stage to deviate from diffusion control. This work provides comprehensive insights into the pH-dependent interfacial interactions and kinetics governing TCH removal by corncob-derived, phosphoric acid-activated biochar.