The cleaning behavior of a soil with physical properties that depend on the wetting time is studied experimentally via the local phosphorescence detection method and simulated numerically in fully developed plane channel flow for Reynolds numbers up to 30,000. A computationally inexpensive general cleaning model is proposed, adopting an existing removal model and coupling it to the turbulent flow field. The influence of the soil on the flow is neglected and the transient behavior of the soil during cleaning is modeled in the form of a transient Dirichlet boundary condition. This approach is innovative for computational fluid dynamics of this phenomenon. The way of determining the model parameters from the experiment is described. The comparison of the simulation results with experimental data reveals very good suitability of the model in the case of a starch soil. A similar good agreement is found for data for a model protein foulant in tube flow from the literature.
The cleaning behavior of a pre-wetted soil is studied experimentally and modeled numerically for the prototypical case of plane channel flow. One of the channel walls is soiled with a food-based model soil containing luminescent tracer particles to perform space- and time-resolved investigations of the cleaning process. Pre-wetting is applied for a few minutes before the soil removal is started with flow of Reynolds number up to 20,000. Physical model and simulation are based on a transient boundary condition to represent the behavior of the soil. Pre-wetting is taken into account by an initial removal of a certain amount of soil due to cohesive separation and the subsequent cleaning modeled as being limited by a diffusive process. Compared to a conventional multiphase simulation, the computation time is lowered by about three orders of magnitude. The results obtained with this elementary approach match the experiments astonishingly well.
Predicting the cleaning time required to remove a thin layer of soil is a challenging task and subject of current research. One approach to tackle this problem is the decomposition into physical sub-problems which are modelled separately and the subsequent synthesis of these models. In this paper, an existing model for adhesive detachment is extended for the prediction of the cleaning time of cohesively separating soil layers. The extension is based on measurements of the pull-off forces and their correlation to the local water mass fraction. The resulting new model is validated using cleaning experiments with starch in a fully developed channel flow. Furthermore, an inhomogeneous soil distribution and its effect on cleaning results like cleaning time and removal rate is investigated. It is shown that accounting for the local soil distribution in the model leads to a significant improvement of the prediction of the cleaning behaviour.
Impinging circular free-surface water jets are used in challenging cooling and cleaning tasks. In order to develop simulation models for process optimization, validation data are required, which are currently not available. Therefore, the flow field of these jets is studied for the first time with the novel laser Doppler velocity profile sensor. The mean velocity field and fluctuations are measured within the stagnation and adjacent redirection region for radial coordinates up to three times the nozzle diameter. In the examined parameter range with jet velocities up to 17 m/s and nozzle diameters up to 5.2 mm, i.e., Reynolds numbers up to 69 500, thin films of a few hundred micrometers are formed, which hinder the measurement with common optical measuring systems. Based on the measurement results, a comparatively low-cost volume of fluid simulation model is developed and validated that presumes a relaminarized film flow. The profiles measured and the simulated flow show very good agreement. In the future, the simulation model provides a basis for process optimization and the innovative measurement technology used will prospectively provide further detailed insights into other flows with high velocity gradients.
Fluid mechanical conditions are crucial for cavitation formation, and significantly influence chemical reactivity. This study investigates process conditions such as pressure, degassing, cavitation and reaction volume, and the sound emission of oxidative dye degradation by cavitation. For ensuring comparability and scalability, dimensionless similarity numbers aligned to the process were introduced. A further focus of the paper is reproducibility with corresponding guidelines. Measurements of dye degradation were carried out without additional chemicals. The oxidation process was assessed by the chemiluminescence of luminol. For this purpose, configurations with three nozzle sizes at different pressure differences were investigated. The generated cavitating jet was captured by imaging techniques and correlated to degradation. The most energy-efficient configuration was obtained by the smallest nozzle diameter of 0.6 mm at a pressure difference of 40 bar. Significant degassing occurred during cavitation. It was more pronounced with smaller nozzle diameters, correlating with higher degradation. Furthermore, discontinuous treatment methods can improve efficiency. Scaling to higher flow rates through multiple reactors in parallel proved more effective, compared to increasing the nozzle diameter or the pressure difference. For the same treated volume, two parallel reactors increased degradation by a factor of 1.35. The insights provide perspectives for optimizing jet cavitation reactors for water treatment.