Crashworthiness is a passive device that has an important function as an absorbing component of the impact energy resulting from an accidental event. The main problem in the crashworthy design is the dimensional limitation on the front end of the vehicle with the driver so that most of the energy absorption is limited. Besides, the complexity of crashworthiness design is difficult to make conventionally. This research aims to find out the effectiveness of crashworthiness design in energy absorption and the resulting deformation patterns. Crashwortines are made in a multi-cell shape using PLA material and printed using a 3D printing raise machine. Crashworthiness is produced with four variation shapes of a Multi-cell circle (MCC), Multi-Cell square (MCS), Multicell pentagonal (MCP), and Multi-Cell pentagonal circles (MCPC) with a side thickness of 2 mm and a length of 150 mm. Experimental quasi-static testing is carried out in the frontal direction using a UTM machine at an operating speed of 2mm/s. The results of the study show that the design of the crash box of the pentagon circle has a significant increase in the energy absorption value of 62.49%, which can be recommended in future impact resistance tube designs. The characteristics of the deformation pattern and the failure resulting from the crashworthiness tend to form the pattern of the bending lamina failure. Failures can occur due to plastic fold, elastic bend, and pressure deformation mechanisms followed by new folding formations (lobes).
31 October 2018 in International Review of Mechanical Engineering (IREME)
An optimal wing configuration is crucial for achieving the best performance during various flight phases, including take-off, cruising, and landing. Such configurations also contribute to maximizing the aircraft's cruising range. This study compares the aerodynamic performance of NACA 43018 wings under different conditions: without high-lift devices, with a slotted flap, and with a combination of a leading-edge slat and slotted flap. Numerical simulations were conducted using the k-ɛ Realizable turbulence model at twelve different angles of attack, with a flow speed of 120 m/s. The results demonstrate that multiple-element wings significantly improve aerodynamic performance, particularly at low angles of attack, by reducing the induced drag coefficient and delaying flow separation.
1 January 2021 in Journal of Physics: Conference Series
The upper surface of the wing is constantly observed by experts on the wing. In this area, a variety of phenomena cause how much aerodynamic performance is demonstrated. Changing or adding geometry to the wing changes the flow characteristics of the upper surface. The use of winglets will certainly change the flow characteristics around the wingtip which will have a large effect on the area behind and next to the winglet itself. This research was carried out using Ansys 19.1 and the turbulent k-ω SST model. The airfoil used is Eppler 562 which is commonly used in unmanned aerial vehicles. Freestream flow velocity that will be used is 10 m/s (Re = 2.34 x 104) with an angle of attack (α) = 12° and 15°. From this study, it was found that the pressure contour in the y-z plane showed a reduction in area and intensity through the use of winglets. Secondary flow formed by using the forward wingtip fence results in a smaller area around the wingtip area than other configurations. Besides, the value of pressure on the upper surface which is equipped with a forward wingtip fence shows that pressure is still quite high when compared to the others.
15 January 2022 in Journal of Mechanical Engineering
On airplanes and UAVs, a stall is something that is always attempted to avoid. Stalling can also be aided by the employment of planform wings with varying geometry. Curved wing variations are often used in UAV applications, especially at low Reynolds numbers. This study discusses stall behavior on rectangular, elliptical, semi-elliptical, and Schuemann wings. Numerical simulations were performed using the turbulent k-ω SST model using Ansys Fluent 19.1. The airfoil used in this study was Eppler 562 at Reynolds number 2.34 x 104 . The angles of attack observed were 0o , 2o , 4o , 6o , 8o , 10o ,12o , 15o , 17o , 19o , and 20o . The Schuemann wing has the best performance that is indicated by the delaying of the stall point, which is at an angle of attack α = 15o , while the rectangular wing produces the highest lift to drag ratio compared to other planform wings. The confluence of the main flow and backflow forms towards the mid-span as the angle of attack increases. The rectangular wing produces high vorticity in the wingtip area due to the tip- vortex phenomenon, while the elliptical and Schuemann wing in the leading edge area due to the geometry of the leading edge.
Airfoil modeling is very important especially in determining the airfoil’s performance. One very important in the airfoil design is how to make airfoil with high lift and low drag to obtain a large lift to drag ratio. In this study, the design was carried out with Eppler 562 wing airfoil by adding an endplate at the end of the wing. Endplate used in the form of forward wingtip fence. The addition of endplate at the tip of the wing aims to reduce the occurrence of tip vortex. The emergence of a tip vortex is due to the flow from the lower surface to the upper surface. These tip vortex can cause induced downwash velocities and reduce effective angle of attack. This research is conducted by numerical simulation using simulation software with turbulent model k-ω SST. Freestream flow rate to be used is 10 m/s with angle of attack (α) = 0°, 2°, 4°, 6°, 8°, 10°,12° 15°, 17° and 19°. On forward wingtip fence cant angel 90° produce higher performance than other wing start at α = 6° while forward wingtip fence cant angel 75°.produce better performance at α = 19°. The tip vortices formed by the winglet produce very different shapes to each other and it appears to be a significant effect of the flow field above the wing surface. These vortices will change shape when the angle of attack of the model is changed. The values of the vortices behind the winglet are also different which indicate the effect of induced drag.