Geopolymer foams are excellent materials in terms of mechanical loads and fire resistance applications. This study investigated the foaming process of geopolymers and foam stability, with a focus on the fire resistance performance when using polystyrene as the base layer. The main purpose is to define the influence of porosity on the physical properties and consequently to find applications and effectiveness of geopolymers. In this study, lightweight materials are obtained through a process called geopolymerization. Foaming was done by adding aluminum powder at the end of the geopolymer mortar preparation. The interaction between the aluminum powder and the alkaline solution (used for the binder during the mixing process) at room temperature is reactive enough to develop hydrogen-rich bubbles that increase the viscosity and promote the consolidation of geopolymers. The basic principle of thermodynamic reactions responsible for the formation of foams is characterized by hydrogen-rich gas generation, which is then trapped in the molecular structure of geopolymers. The geopolymer foams in this study are highly porous and robust materials. Moreover, the porosity distribution is very homogeneous. Experimental assessments were performed on four specimens to determine the density, porosity, mechanical strength, and thermal conductivity. The results showed that our geopolymer foams layered on polystyrene boards (with optimal thickness) have the highest fire resistance performance among others. This combination could withstand temperatures of up to 800 °C for more than 15 min without the temperature rising on the insulated side. Results of the best-performing geopolymer foam underline the technical characteristics of the material, with an average apparent density of 1 g/cm3, a volume porosity of 55%, a thermal conductivity of 0.25 W/mK, and excellent fire resistance.
This study examines the impact of calcium-rich fly ash as an additive on metakaolin-based geopolymers. Six types of fly ash (FA1-FA7) from different thermal power plants in the Czech Republic were collected and characterized based on their physical and chemical properties. The addition of fly ash into the geopolymers was evaluated through a multicriteria assessment that focused on density and mechanical properties. By using a multi-criteria approach, the assessment provides a comprehensive and holistic evaluation of the material, allowing for a more informed decision about the optimal addition of additives. This approach helps to minimize any negative impact on the material’s properties while maximizing the utilization of the by-product. The result is an optimized geopolymer mixture with improved properties and increased sustainability, as the by-product is used beneficially. Furthermore, calcium content is the key factor that affects the physical properties of geopolymers by accelerating the curing time. This rapid process can result in reduced strength with increasing fly ash content. The multicriteria assessment revealed that the optimal condition is achieved using fly ash (FA2) from the Loucovice thermal power plant (5.2 wt.% Ca) that was treated at a temperature of 615 °C. The flexural strength of FA2-based geopolymers increased by 13% compared to concrete (standard). However, the addition of fly ash significantly reduced the compressive strength of geopolymers throughout the range of specimens. The Charpy impact strength of FA2 was higher than the standard due to the presence of unburned biomass solids in the ash structure that can absorb energy easily.
The results of statistical processing of vibration signals obtained during diagnostics of ship power plants during the operation process are offered. A distinctive feature of monitoring the technical condition of elements of ship power plants is the uncertainty in the fixation and duration of extreme loads. The peculiarity of computer vibration diagnostics of rotary mechanisms is determined, which is that, in particular, physical measurements of vibration signals require their use in mathematical models of the physical state of the bearing. Calculations of statistical characteristics of vibration signals in the time domain, such as standard deviation (Std), asymmetry (Skewness), kurtosis (Kurtosis), full range of oscillations (Peak2Peak), root mean square value (RMS), cross factor (CrestFactor), form- factor (ShapeFactor), impulse factor (ImpulseFactor), marginal factor (MarginFactor), energy (Energy). The variety of diagnostic signals leads to the need to merge indicators of different dimensions without losing available information into a single generalizing indicator, for which the method of principal components is used in the work. The methodology of statistical processing and practical implementation of diagnostics of vibration signals during the analysis of damage evolution of rolling bearings of turbochargers of marine power plants are described. A new computer information parameter of vibration diagnostics based on the analysis of the first principal component in the time domain and spectral excess in the frequency domain has been identified and experimentally confirmed. The use of new diagnostic parameters makes it possible not only to judge the degree of damage to the rolling bearing, but also to observe the dynamics of the development of the defect and make a relative forecast of the working life of the rolling bearing. A real practical situation is considered - computer diagnostics of vibration signals of ship rolling bearings of a point defect of an external defect of a rolling bearing ring. Determining the applicability of the principal component method to other types of defects showed their potential for vibrodiagnosis of defects located on the inner ring of the bearing and when the ball falls out of the holder.
Presented here is a constructive solution to the challenge of utilizing the diffraction phenomenon for mitigating noise around roadside objects caused by the movement of vehicles on transportation routes. In contrast to existing prototypes, the innovation of the proposed solution lies in the creation of an active system that concentrates and directs oscillations originating from transportation sources. This active system, centered around sound absorption and reflection, establishes protective barriers and focuses on sound vibrations. The incorporation of diffraction effects within the Fraunhofer zones, along with the utilization of Fresnel lenses, directs attention towards these vibrations. The technical objective of harnessing the diffraction phenomenon for noise reduction around roadside objects involves demonstrating the feasibility of using a Fresnel zone plate (FZP) tailored for a specific oscillation frequency. This plate should demonstrate the ability to effectively manipulate sounds of varying frequencies while retaining its diffractive focusing capabilities. The intrinsic frequency characteristics of diffractive elements cannot be eliminated due to the inherent nature of sound diffraction. Consequently, it is imperative to thoroughly investigate and account for these properties. A groundbreaking discovery has been made, confirming the phenomenon of noise concentration originating from transportation sources. This revelation suggests that when a FZP is employed at frequencies other than its designed frequency, the concentration of oscillations remains. However, only the focal point of concentration shifts. Through experimentation, it has been established that the same FZP can be employed for varying wavelengths within a range of approximately ±20% while adhering to diffraction conditions. The feasibility of employing the thin lens formula to focus oscillations following the passage through a FZP has been substantiated. This solution also delves into the principal focusing, frequency, and shaping characteristics of the diffractive elements within FZPs. Furthermore, a computed estimation of the acoustic field scattered by a diffraction grating is compared against experimental data. This validates the approach and its efficacy in practical scenarios. The potential of harnessing the diffraction phenomenon to concentrate and regulate noise from transportation sources, thereby safeguarding roadside objects, is presented as a promising avenue for exploration.
Geopolymer composite materials are a viable alternative to conventional construction materials. The research problem of geopolymer composites revolves around the imperative to comprehensively address their synthesis, structural performance, and environmental impact. The derived mathematical model facilitates precisely determining the optimal proportions of two crucial constituents in the geopolymer matrix: silica sand and secondary aluminium by-product. A mathematical model for optimising the composition of geopolymer composites has been developed based on the integrated use of Markov chains, criterion methods and orthogonally compositional plan. The optimal composition of the geopolymer matrix is determined and predicted using a mathematical model. Specifically, the recommended content mixing ratio is as follows: metakaolin at 1000 g, activator at 900 g, silica fume at 1052.826 g, carbon fibre at 10 g, and secondary aluminium by-product at 62,493 g. Analysing the influence of different secondary aluminium industry by-products on the geopolymerization process, and assessing the mechanical, thermal, and environmental properties of the resulting composites to establish a comprehensive understanding of their structural viability.
Geopolymer composite materials are a viable alternative to conventional construction materials. The research problem of geopolymer composites revolves around the imperative to comprehensively address their synthesis, structural performance, and environmental impact. The derived mathematical model facilitates precisely determining the optimal proportions of two crucial constituents in the geopolymer matrix: silica sand and secondary aluminum by-product. A mathematical model for optimizing the composition of geopolymer composites has been developed based on the integrated use of Markov chains, criterion methods, and an orthogonally compositional plan. The optimal composition of the geopolymer matrix is determined and predicted using a mathematical model. Specifically, the recommended content mixing ratio is as follows: metakaolin at 1000 g, activator at 900 g, silica fume at 1052.826 g, carbon fibre at 10 g, and secondary aluminum by-product at 62.493 g. This study analyzes the influence of different secondary aluminum industry by-products on the geopolymerization process and assesses the mechanical, thermal, and environmental properties of the resulting composites to establish a comprehensive understanding of their structural viability.