The stable homogeneous dielectric barrier discharge (DBD) is obtained in atmospheric 2–3 mm air gap. It is generated using center frequency 1 kHz high voltage power supply between two plane parallel electrodes with specific alumina ceramic plates as the dielectric barriers. The discharge characteristics are studied by a measurement of its electrical discharge parameters and observation of its light emission phenomena. The results show that a large single current pulse of about 200 μs duration appearing in each voltage pulse, and its light emission is radially homogeneous and covers the entire surface of the two electrodes. The homogeneous discharge generated is a Townsend discharge during discharge. The influences of applied barrier, its thickness, and surface roughness on the transition of discharge modes are studied. The results show that it is difficult to produce a homogeneous discharge using smooth plates or alumina plate surface roughness Ra < 100 nm even at a 1 mm air gap. If the alumina plate is too thin, the discharge also transits to filamentary discharge. If it is too thick, the discharge is too weak to observe. With the increase of air gap distance and applied voltage, the discharge can also transit from a homogeneous mode to a filamentary mode. In order to generate stable and homogeneous DBD at a larger air gap, proper dielectric material, dielectric thickness, and dielectric surface roughness should be used, and proper applied voltage amplitude and frequency should also be used.
22 December 2020 in IEEE Transactions on Plasma Science
In order to study the effect of surface morphology of dielectric materials on features of dielectric barrier discharge (DBD) in air at atmospheric pressure (AP), electrical characteristics and optical emission spectrum are obtained in a 2-mm air gap with quartz glass and ceramic used as the dielectric layer (the capacitance of the used dielectrics is similar). The transition of discharge mode is observed for different dielectric material and surface morphology. Results show that with varying dielectric material and surface morphology, air atmospheric pressure dielectric barrier discharge (APDBD) presents three discharge modes, including a filamentary mode, a homogeneous mode, and a mixed mode of them. Further investigation reveals that the homogenous mode is in a Townsend discharge regime, which is realized in a proper surface morphology of 96% Al 2 O 3 ceramic. Moreover, optical emission spectrum is obtained, which mainly consists of atomic lines of nitrogen and molecular bands originating from the second positive system of N 2 ( $\text{C}^{3}\Pi _{\mathrm {u}}\to \text{B}^{3}\Pi _{\mathrm {g}}$ ). From N 2 ( $\text{C}^{3}\Pi _{\mathrm {u}}\to \text{B}^{3}\Pi _{\mathrm {g}}$ ), molecular vibrational temperature is investigated as a function of surface roughness ( $R_{\mathrm {a}}$ ) of the different dielectric materials. Result reveals that there is a minimal vibrational temperature when the discharge is in the homogeneous mode. With quartz glass used as the dielectric, the vibrational temperature decreases first and then increases with increasing $R_{\mathrm {a}}$ . The minimum value appears at $R_{\mathrm {a}}$ of 215 nm. Besides, the discharge current is the most concentrated in time, and the discharge looks the most homogeneous under this circumstance.
Large-scale plumes in a plasma jet are desirable for fast processing of materials with large surface, which are normally composed of discharge filaments. A filamentary plume may cause nonuniform treatment or even damage to vulnerable samples. In this Letter, an argon plasma jet in a gas-confined barrier discharge geometry is proposed to generate a large-scale filament-free plume. Results indicate that the filament-free plume can only be sustained in a relatively low voltage amplitude (Vp), which transits to the filamentary plume with increasing Vp. There is only one negative discharge per voltage cycle for the filament-free plume, while both positive and negative discharges for the filamentary plume. Fast photography reveals that the negative discharge is diffuse, originating from the propagation of a negative streamer. On the contrary, the positive discharges are filamentary. Optical emission spectroscopy indicates that the filament-free plume has lower electron density, electron excitation temperature, and molecular vibrational temperature compared to the filamentary plume, while gas temperature keeps at a low value with varying Vp.
Being able to generate a remote plasma plume, the atmospheric pressure plasma jet has become an indispensable tool for extensive application fields. A plasma plume usually has a straight column morphology, which results from straight-line or stochastic snake-like propagations of streamers. The snake-like propagation of streamers is unclear in the mechanism. In this paper, a meandering plume is generated for the first time downstream of an argon plasma jet excited by a positively biased sinusoidal voltage, which transits from a straight column plume with an increasing bias voltage (Vb). Results indicate that the wavelength of the meandering plume is inversely proportional to voltage frequency and directly proportional to the gas flow rate. For every voltage cycle, integrated light emission from the meandering plume presents one pulse with low Vb and two pulses with high Vb. Fast photography reveals that the meandering plume results from repeated snake-like propagations of positive streamers due to the influence of ion clouds. To confirm the existence of ion clouds, an opposite argon flow is introduced. With wiping off ion clouds in the argon stream, the meandering plume gradually turns back to a straight column with an increasing opposite flow rate. All these phenomena mentioned above have been explained qualitatively on the basis of ion clouds. These results may shed light on the streamers' dynamics in the atmospheric pressure plasma jet.
8 August 2022 in IEEE Transactions on Radiation and Plasma Medical Sciences
Atmospheric pressure plasma jets have great potentials for various biomedical applications due to abundance with active oxygen species. In this paper, an air plasma jet with a geometry of micro-hollow cathode discharge has been developed, which operates in a pulsed mode or a continuous mode depending on the dissipated power of the plasma jet. There are some continuous spectra emitted from the plasma jet, whose integrated intensity indicates that electron density increases with the increase of dissipated power, while decreases with increasing air flow rate for both of the two modes. Moreover, electron density in the continuous mode is higher than that in the pulsed mode. Gas temperature of the plasma jet is obtained by the best fitting of the simulated and the experimental optical emission spectrum of OH (A-X), and ozone concentration produced by the plasma jet is measured by means of ultra-violet absorption spectroscopy. Results indicate that both ozone concentration and gas temperature decrease with increasing distance from the jet nozzle. At the jet nozzle, both of them increase with increasing dissipated power. However, ozone concentration decreases, while gas temperature increases with increasing air flow rate. The results are very important for the biomedical application of plasma jet.
27 May 2022 in IEEE Transactions on Plasma Science
Atmospheric pressure glow discharge above water anode has attracted much attention due to its extensive potential applications, where self-organized patterns can be formed. Usually, they are time-invariant under constant conditions. In this article, some peculiar time-dependent patterns are formed, among which concentric ring patterns like single, triple, quadruple, and quintuple rings are observed in water-anode discharge system for the first time. Accompanying the increasing complexity of patterns, results indicate that water conductivity evolves with time. Optical emission spectroscopy reveals that before reaching constant values, electron density decreases, while electron and gas temperatures increase as time elapses. Interestingly, the temporal variations of electric conductivity and plasma parameters are correlated with the evolution of patterns. Based on the phenomena mentioned above, the pattern evolution is qualitatively explained based on the Turing mechanism at last. We think these results will shed light on formation mechanism of patterns in atmospheric pressure glow discharge with water anode.