Mathias Flansbjer

Dr. Mathias Flansbjer

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2017 in Composite Structures
Verified
Journal Article
Closed access
NPNatalie Williams Portal
Natalie Williams Portal
MFMathias Flansbjer
Mathias Flansbjer
KZKamyab Zandi
Kamyab Zandi
LWLech Wlasak
Lech Wlasak
KMKatarina Malaga
Katarina Malaga

1 September 2017 in Optics and Lasers in Engineering
Verified
Journal Article
Open access
ACA.F. Cinar
A.F. Cinar
SBS.M. Barhli
S.M. Barhli
DHD. Hollis
D. Hollis
MFMathias Flansbjer
Mathias Flansbjer
RTR.A. Tomlinson
R.A. Tomlinson
MMMahmoud Mostafavi
Mahmoud Mostafavi

25 January 2012 in Materials and Structures
Verified
Journal Article
Closed access
PDF file
AJAnette Jansson
Anette Jansson
MFMathias Flansbjer
Mathias Flansbjer
ILIngemar Löfgren
Ingemar Löfgren
KLKarin Lundgren
Karin Lundgren
KGKent Gylltoft
Kent Gylltoft

1 March 2016 in Journal of Building Engineering
Verified
Journal Article
Closed access
NPNatalie Williams Portal
Natalie Williams Portal
MFMathias Flansbjer
Mathias Flansbjer
PJPär Johannesson
Pär Johannesson
KMKatarina Malaga
Katarina Malaga
KLKarin Lundgren
Karin Lundgren

8 February 2020 in Rock Mechanics and Rock Engineering
Verified
Journal Article
Open access
PDF file
JLJ. Larsson
J. Larsson
MFMathias Flansbjer
Mathias Flansbjer
Applying accurate normal load to a specimen in direct shear tests under constant normal stiffness (CNS) is of importance for the quality of the resulting data, which in turn influences the conclusions. However, deficiencies in the test system give rise to a normal stiffness, here designated as system normal stiffness, which results in deviations between the intended and actual applied normal loads. Aiming to reduce these deviations, this paper presents the effective normal stiffness approach applicable to closed-loop control systems. Validation through direct shear tests indicates a clear influence of the system normal stiffness on the applied normal load (13% for the test system used in this work). The ability of the approach to compensate for this influence is confirmed herein. Moreover, it is demonstrated that the differences between the measured and the nominal normal displacements are established by the normal load increment divided by the system normal stiffness. This further demonstrates the existence of the system normal stiffness. To employ the effective normal stiffness approach, the intended normal stiffness (user defined) and the system normal stiffness must be known. The latter is determined from a calibration curve based on normal loading tests using a stiff test dummy. Finally, a procedure is presented to estimate errors originating from the application of an approximate representation of the system normal stiffness. The approach is shown to effectively reduce the deviations between intended normal loads and the actual applied normal loads.

18 August 2011 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
MFMathias Flansbjer
Mathias Flansbjer
TSTorsten Sjögren
Torsten Sjögren
The use of aluminium in lightweight structures and corrosive environments is continuously increasing. Welding is often used to assemble different aluminium components and it is of great importance to take into account the deteriorating effect the welding operation on the aluminium’s strength when designing these structures. In the present study, the strain-fields of welded aluminium tensile specimens have been analysed by digital image correlation (DIC) techniques, micro hardness measurements and finite element (FE) modelling. The stress-strain curve of the weld material, the heat affected zone (HAZ) and the base material have been determined by tensile tests. The material properties and the extension of the HAZ were also correlated to the micro hardness. The experimental data has been used as an input to the material models of the FE analysis. The study shows that using FE-analysis in combination with strain-field determination by DIC is very powerful. The resulting strain-fields are easily compared and the FE-analysis is verified in a straightforward way. Furthermore, the results of the study suggest that micro hardness measurements could be used to derive the strength of the material affected by the welding operation.