Mitigating formation damage due to fines migration is crucial for maintaining reservoir productivity in enhanced oil recovery (EOR) processes. This research introduces a novel composite, Titanium dioxide nanoparticles coated with Saponin and Zirconium (TiO2@Saponin/Zr(IV)), synthesized via a sol–gel method, to address this challenge, particularly in low salinity water injection scenarios. Characterization through FT-IR confirmed successful functionalization, indicated by the Zr–O band at 480 cm−1 and saponin bands around 1030–1085 cm−1 and 2919–2850 cm−1. Zeta potential measurements showed that in low salinity brine, quartz and kaolinite exhibited highly negative potentials of − 32 mV and − 45 mV, respectively, while TiO2@Saponin/Zr(IV) displayed a positive potential of + 19 mV. Importantly, mixtures of quartz and kaolinite with TiO2@Saponin/Zr(IV) in low salinity conditions resulted in moderated zeta potentials of + 3 mV and − 2 mV, indicating surface charge modulation. Core flooding experiments further validated the composite’s effectiveness. Injecting high salinity water resulted in a minor permeability reduction from 90 to 78 mD, while low salinity water injection caused a drastic drop from 90 to 8 mD. However, with the introduction of 0.5 wt% TiO2@Saponin/Zr(IV) in low salinity water, the permeability reduction was significantly controlled, decreasing from 90 to 85 mD. These quantitative results demonstrate that TiO2@Saponin/Zr(IV) effectively mitigates fines migration by modifying surface charge and preserving permeability, offering a promising solution for formation damage control and enhanced oil recovery.
Polyethylene glycol (PEG), a synthetic polymer made up of repeating ethylene oxide units, is widely recognized for its broad utility and adaptable properties. Precise estimation of CO2 solubility in PEG plays a vital role in enhancing processes such as supercritical fluid extraction, carbon capture, and polymer modification, where CO2 serves as a solvent or transport medium. This study focuses on building advanced predictive models using machine-learning approaches, such as random forest (RF), decision tree (DT), adaptive boosting (AdaBoost), k-nearest neighbors (KNN), and ensemble learning (EL) to forecast CO2 solubility in PEG across a wide range of conditions. The data utilized for model development is sourced from previously published literature, and an outlier detection method is applied beforehand to identify any suspicious data points. Additionally, sensitivity analysis is performed to evaluate the relative influence of each input parameter on the output variable. The results proved that DT model is the most performance method for estimating CO2 solubility in PEG since it showed largest R-squared (i.e., 0.801 and 0.991 for test and train, respectively) and lowest error metrics (MSE: 0.0009 and AARE%: 22.58 for test datapoints). In addition, it was found that pressure and PEG molar mass directly affects the solubility in contrast to the temperature variable which has an inverse relationship. The developed DT model can be regarded accurate and robust user-friendly tool for estimating CO2 solubility in PEG without needing experimental workflows which are known to be time-consuming, expensive and tedious.
Mud loss during drilling operations poses a significant problem in the oil and gas industry due to its contributions to increased costs and operational risks. This study aims to develop a reliable predictive model for mud loss volume using machine learning techniques to improve drilling efficiency and reduce non-productive time. The dataset consists of 949 field records from Middle Eastern drilling sites, incorporating variables such as borehole diameter, drilling fluid viscosity, mud weight, solid content, and pressure differential. Initial data analysis included statistical evaluation, outlier detection using leverage diagnostics, and data normalization to ensure validity and consistency. A Gradient Boosting Machine (GBM) served as the core predictor, with its hyperparameters fine-tuned using four optimization strategies: Evolution Strategies (ES), Batch Bayesian Optimization (BBO), Bayesian Probability Improvement (BBI), and Gaussian Process Optimization (GPO). Model performance was evaluated using k-fold cross-validation, with metrics including R², mean squared error and average absolute relative error percentage. Results demonstrated that the GBM-BPI achieved the strongest test performance (R² = 0.926, MSE = 1208.77, AARE% = 26.73), outperforming other approaches in accuracy and stability. Feature importance assessed through SHAP analysis revealed that hole size, formation type, and pressure differential were the most influential variables, while solid content had minimal effect.
The primary objective of this study is to develop and validate robust data-driven models for accurately predicting bacterial growth inhibition induced by c
Eco-friendly biopolymers in water-based drilling fluids often suffer from thermal degradation and inadequate filtration control under harsh downhole condit
Efficient extraction of subsurface resources relies heavily on the performance of drilling fluids, which necessitates constant innovation in their formulation. This study introduces a novel Polylactic Acid/Henna composite for significant enhancement of drilling fluid properties. The composites was characterized via Scanning Electron Microscopy (SEM), Energy-Dispersive X-ray Spectroscopy (EDS), and Fourier-Transform Infrared Spectroscopy (FTIR), confirming the uniform Henna particles dispersion in PLA matrix. The composite was added to water-based drilling fluids at concentrations of 0.5 wt%, 1 wt%, 2 wt%, 4 wt%, and 10 wt%, followed by rigorous evaluation of rheological and filtration performance. Experimental results demonstrated that fluids containing 2 wt% PLA/Henna composite exhibited the best performance, with a 32% increase in yield point and a 21% improvement in plastic viscosity compared to the base fluid. Furthermore, filtration volume decreased by 42%, while spurt loss was reduced by 35% due to improved filter cake formation. These quantitative improvements optimize fluid efficiency and minimize permeability, enhancing the ability to control fluid loss under simulated drilling conditions. Such enhancements promote better wellbore stability and operational reliability.