Cellulose nanopaper (CNP) is of great interest to researchers mainly due to its renewability, excellent mechanical properties and optical properties. However, CNP is usually sensitive to water, resulting in the loss of strength and durability. To overcome this issue, in this work, an efficient and sustainable route, which involved ammonium sulfite cooking and formic acid hydrolysis, was reported to isolate lignin-containing cellulose nanofibrils (CNFs) from tobacco stalk. The resultant CNFs were directly used to fabricate strong, flexible, and water resistant CNP without any complex chemical modification. The residual lignin was found to act as a reinforcing agent between CNFs in CNP. The tensile strength and toughness of the lignin-containing CNP (255 MPa and 19.7 MJ m−3) were much higher compared with those of the one without lignin (179 MPa and 12.8 MJ m−3). The water-resistance of the CNP was also improved extraordinarily, and its maximum wet tensile strength reached up to 83 MPa which is the highest value in comparison with the reported CNP. Compared to the lignin-free CNP, the lignin-containing CNP also showed the better thermal stability and excellent UV-blocking properties. The present work designed a new route to prepare lignin-containing CNFs and CNP, which are potential candidates to replace petroleum-based materials in many advanced applications.
Aqueous two‐phase emulsion (ATPE)‐based bioinks, a creative innovation for bioprinting, enable the fabrication of complex 3D cell‐laden hydrogels with macroporous structure, which promote cellular activities within the scaffold. However, these bioinks intrinsically lack stability and specific biofunctionality, potentially limiting their application for targeted tissue engineering. This study proposes a new perspective by introducing less than 0.1% phosphorylated cellulose nanofibrils (pCNF), a 1D nanofibril top‐down produced from natural biomasses, into a dextran/methacrylated gelatin (GelMA)‐based ATPE system for extrusion‐based bioprinting of preosteoblastic cells, aiming to fabricate macroporous hydrogels with osteogenic differentiation potential. The pCNF that is selectively partitioned in the GelMA phase can not only improve the emulsion stability and alter the rheological behaviors of the ATPE‐based bioink, but also enhance the damping capacity and mineralization ability of the crosslinked hydrogels. Furthermore, macroporous hydrogels with pCNF demonstrate increased cell activity and higher viability in post‐printing, along with higher alkaline phosphatase activity and osteoblastic gene expression. Importantly, the organized interfaces within the hydrogel facilitate the formation of macroscopic biomineralized nodules in vitro. The incorporation of multifunctional pCNF in the ATPE system significantly boosts the physiochemical and biological performance of the macropore‐forming bioink, transforming them into a suitable platform for engineering in vitro bone models.
Microgel assembly as void‐forming bioinks in 3D bioprinting has evidenced recent success with a highlighted scaffolding performance of these bottom‐up biomaterial systems in supporting the viability and function of the laden cells. Here, a ternary‐component aqueous emulsion is established as a one‐step strategy to integrate the methacrylated gelatin (GelMA) microgel fabrication and assembly through vat photopolymerization in situ using digital light processing (DLP)‐based bioprinting. The as‐proposed aqueous emulsion is featured with the partitioning of a secondary photo‐crosslinkable polysaccharide, methacrylated galactoglucomannan (GGMMA) derived from plant source in both the dispersed phase of GelMA droplets and the continuous phase of dextran (Dex). As an emulgator, GGMMA renders enhanced stability of the aqueous emulsion bioresins. Strategically, the photo‐crosslinkable GGMMA adheres the GelMA microgels that are conveniently converted from emulsion droplets to form hydrogel construct in layer‐by‐layer curing to accommodate the laden cells directly mixed in the aqueous emulsion. The spatially interconnected void space left by the removal of Dex benefits the cell growth under the guidance of the microgel surface and supports cell colonization within the macroscopic porous hydrogel. This work amends a low‐concentration and cost‐effective bioresin that is highly applicable for facilely fabricating microgel assembly as a porous hydrogel construct in DLP‐based bioprinting.
Utilizing naturally derived biopolymers in the macromolecular design of thermoresponsive polymers offers sustainable and biodegradable smart building blocks to functional materials. Here, a novel graft polymer of xylan‐g‐allyl glycidyl ether (xylan‐g‐AGE) that is thermoresponsive to self‐assemble and photoreactive in photopolymerization is reported. This research highlights an innovative use of the debranched wood xylan, a chemically engineered linear polysaccharide of β‐1,4‐linked xylose, as the backbone in grafting polymer, which allows a greater degree of spatial coordination for sidechains than the analogous cellulose. Induced by the reformation of H‐bonds and hydrophobic effect, xylan‐g‐AGE transits from solvated coil chain to self‐assembled mesoglobules upon the temperature change above its lower critical solution temperature (LCST). When xylan‐g‐AGE is used in photoresins to fabricate hydrogels with good geometric fidelity via DLP 3D printing, solvated xylan‐g‐AGE stiffens the polyethylene glycol (PEG) hydrogel strongly, due to higher crosslink density of available AGE moiety and faster crosslinking rate, while self‐assembled xylan‐g‐AGE toughens the PEG hydrogel better, attributed to the strategy of “dual chemically independent domains” that smartly combines tough domain of PEG and soft domain of self‐assembled xylan‐g‐AGE. Conductive hydrogel is fabricated by incorporating 2D MXene sheets into this hydrogel matrix in DLP printing, which demonstrates superior performance as wearable strain sensors.
Polybutylene adipate-terephthalate (PBAT) offers a convincing ecological alternative to the traditional fossil-based plastics due to its biodegradability and robust mechanical properties. The objective of this study is to develop PBAT-based bio-composite films through incorporating functionalized cellulose nanocrystals (CNC) and curcumin (CUR). In order to improve the interfacial compatibility with the PBAT matrix and co-doping with CUR, CNC was modified using dodecyl succinic anhydride (DxCNC). In this ternary bio-composite system, CUR functioned as a bio-based antioxidant and antimicrobial agent. The presence of CUR also provides excellent UV-shielding properties, whereas the DxCNC effectively enhances the controlled release of CUR. The synergistic effect between DxCNC and CUR in boosting antimicrobial properties, with the inhibition values for E. coli and S. aureus reached 1.82 log CFU/cm2 and 2.12 log CFU/cm2, respectively. These findings indicate DxCNC/CUR/PBAT ternary composite films as a promising material for eco-friendly packaging products.