Microbial load on fresh fruit and vegetables causes decay and losses after harvest and may lead to foodborne illness in case of contamination with human pathogens on raw consumed produces. Washing with tap water only marginally reduces microorganisms attached to produce surfaces. Chlorine is widely used for decontamination on fresh horticultural produces. However, due to harmful by-products and the questionable efficacy it has become increasingly challenged. During the last 20 years, the interest to study ClO₂ treatments as an alternative sanitation agent for industrially prepared fresh produce has largely increased. For a wide range of commodities, the application of gaseous ClO₂ has meanwhile been investigated. In addition, since several years, the interest in aqueous ClO₂ treatments has further risen because of the better manageability in postharvest processing lines compared to gaseous application. This article critically evaluated the effects of postharvest application of aqueous ClO₂, either alone or in combination with other treatments, on microbial loads for various horticultural produces. In laboratory investigations, application of aqueous ClO₂ at concentrations between 3 and 100 ppm effectively reduced counts of natural or inoculated microorganisms (bacteria, yeasts, and mold) in the range of 1 and 5 log. However, various effects of ClO₂ treatments on produce quality have been described. These mainly comprise implication on sensory and visual attributes. In this context, there is increasing focus on the potential impacts of aqueous ClO₂ on relevant nutritional components of produces such as organic acids or phenolic substances.

Mechanical loads cause severe damage to perishable agricultural products. In order to quantify the mechanical impact during harvest and postharvest processes, several electronic fruits have been developed. The objective of the work described here was to compare on a laboratory scale different types of impact acceleration recording electronic fruits: Mikras implanted in a real potato tuber as well as in a dummy tuber, IRD, Smart Spud and TuberLog. The acquisition of mechanical impacts was performed using a drop simulator with optional steel or PVC as impact material as well as a processing line simulator. Our results show that drops from 10 cm height on PVC caused similar peak accelerations of Mikras implanted in a real potato or a dummy, IRD and TuberLog. When dropped onto steel however, IRD, TuberLog and Mikras implanted in a dummy recorded higher peak values than Mikras in real potatoes. Impact on the flat side of a tuber led to higher peak values than impact on the apical region. This could be caused by different elastic compliance of synthetic materials as well as material thickness. Running through the processing line simulator TuberLog recorded the most impact; Smart Spud recorded a low number of impacts compared to the other electronic fruits. In all experiments the least sensitive measurements were recorded using Smart Spud.

Apples are stored at temperatures close to 0 °C and high relative humidity (up to 95%) under controlled atmosphere conditions. Under these conditions, the cyclic operation of the refrigeration machine and the associated temperature fluctuations can lead to localized undershoots of the dew point on fruit surfaces. The primary question for the present study was to prove that such condensation processes can be measured under practical conditions during apple storage. Using the example of a measuring point in the upper apple layer of a large bin in the supply air area, this evidence was provided. Using two independent measuring methods, a wetness sensor attached to the apple surface and determination of climatic conditions near the fruit, the phases of condensation, namely active condensation and evaporation, were measured over three weeks as a function of the operating time of the cooling system components (refrigeration machine, fans, defrosting regime). The system for measurement and continuous data acquisition in the case of an airtight CA-storage room is presented and the influence of the operation of the cooling system components in relation to condensation phenomena was evaluated. Depending on the set point specifications for ventilation and defrost control, condensed water was present on the apple surface between 33.4% and 100% of the duration of the varying cooling/re-warming cycles.

In cold storage facilities of fruit and vegetables, airflow is necessary for heat removal. The design of storage facilities influences the air speed in the surrounding of the product. Therefore, knowledge about airflow next to the product is important to plan the layout of cold stores adapted to the requirements of the products. A new sensing device (ASL, Air speed logger) is developed for omnidirectional measurement of air speed between fruit or vegetables inside storage bins or in bulk. It consists of four interconnected plastic spheres with 80 mm diameter each, adapted to the size of apple fruit. In the free space between the spheres, silicon diodes are fixed for the airflow measurement based on a calorimetric principle. Battery and data logger are mounted inside the spheres. The device is calibrated in a wind tunnel in a measuring range of 0–1.3 m/s. Air speed measurements in fruit bulks on laboratory scale and in an industrial fruit store show air speeds in gaps between fruit with high stability at different airflow levels. Several devices can be placed between stored products for determination of the air speed distribution inside bulks or bin stacks in a storage room.