Nitrogen (N2) and oxygen (O2) are important impurities obtained from carbon dioxide (CO2) capture procedures. Thermodynamic modeling of CO2-N2-O2-brine-minerals is important work for understanding the geochemical change of CO2 geologic storage with impurities. In this work, a thermodynamic model of the CO2-N2-O2-brine-carbonate system is established using the “fugacity-activity” method, i.e., gas fugacity coefficients are calculated using a cubic model and activity coefficients are calculated using the Pitzer model. The model can calculate the properties at an equilibrium state of the CO2-N2-O2-brine-carbonate system in terms of gas solubilities, mineral solubilities, H2O solubility in gas-rich phase, species concentrations in each phase, pH and alkalinity. The experimental data of this system can be well reproduced by the presented model, as validated by careful comparisons in conditions from surface to high temperature and pressure. The model established in this work is suitable for CO2 geologic storage simulation with N2 or O2 present as impurities.
4 August 2014 in Greenhouse Gases: Science and Technology
The Yinggehai Basin is a typical high temperature and high pressure (HTHP) gas-bearing basin. The pressure coefficient exceeds 2.2 in deeply-buried Miocene reservoirs in the Ledong Slope, a nondiapir zone in the Yinggehai Basin. Determining the overpressure mechanisms and predicting the pore pressure are key issues for natural gas exploration and development in the Ledong Slope. In this paper, overpressure mechanisms were investigated according to the analysis of vertical effective stress-logging responses and geological evaluations, and the pore pressure was predicted using the Bowers method. The loading-unloading crossplots indicated that the overpressure that existed in reservoirs mainly consists of two types: neighbor-source and allo-source overpressure. The neighbor-source overpressure is mainly caused by the pressure transmission from the adjacent mudstone to the reservoir, with a pressure coefficient less than 1.51.6. The high-magnitude overpressure points with pressure coefficients greater than 1.6 show a typical unloading response, indicating elevated sandstone pressures rather than in situ mudstone pressures, which are most likely to be generated by overpressure vertical transfer. The high-magnitude overpressure fluid generated by the high mature ultradeep buried N1s source rock migrated to the shallower reservoirs via hidden faults/microfractures, which led to the vertical transfer of overpressure. Vertically transferred overpressure was generated at 1.50.2Ma, which is beneficial for the preservation of overpressure in lenticular sandbodies. The estimated pore pressure by the Bowers method is in good agreement with the measured pressure and provides a meaningful reference for predrilling pressure prediction in nondiapir or diapir zones in the Yinggehai Basin.
A mutual solubility model for CO2-CH4-brine systems is constructed in this work as a fundamental research for applications of deep hydrocarbon exploration and production. The model is validated to be accurate for wide ranges of temperature (0–250°C), pressure (1–1500 bar), and salinity (NaCl molality from 0 to more than 6 mole/KgW). Combining this model with PHREEQC functionalities, CO2-CH4-brine-carbonate-sulfate equilibrium is calculated. From the calculations, we conclude that, for CO2-CH4-brine-carbonate systems, at deeper positions, magnesium is more likely to be dissolved in aqueous phase and calcite can be more stable than dolomite and, for CO2-CH4-brine-sulfate systems, with a presence of CH4, sulfate ions are likely to be reduced to S2−and H2S in gas phase could be released after S2−saturated in the solution. The hydrocarbon “souring” process could be reproduced from geochemical calculations in this work.
Reservoir geological modeling plays a crucial role in characterizing the spatial distribution and heterogeneity of subsurface reservoirs. The exploration of deep oil and gas resources is not only a global trend in the oil industry but also an inevitable choice for China to ensure energy security and achieve sustainable development in the oil and gas industry. Oil and gas exploration and development technologies have also made continuous breakthroughs, providing strong support for the sustained increase in China’s deep and ultra-deep oil and gas production. Deep and ultra-deep oil and gas reservoirs exhibit high levels of heterogeneity, which are governed by the original sedimentation processes and have a significant impact on oil and gas migration and accumulation. However, traditional pixel-based stochastic reservoir modeling encounters challenges when attempting to effectively simulate multiple facies simultaneously or objects with intricate internal hierarchical architectures. To address the characterization of highly heterogeneous deep and ultra-deep oil and gas reservoirs, this study defines unit architecture bodies, such as point bars, braided rivers, and mouth bars, incorporating internal nested hierarchies. Furthermore, a novel object-based stochastic modeling method is proposed, which leverages seismic and well logging interpretation data to construct and simulate reservoir bodies. The methodology is rooted in the unit element theory. In this approach, sedimentary facies models are stochastically constructed by selecting appropriate unit elements from a database of different sedimentary environments using Sequential Indicator Simulation. The modeling process is constrained by time sequence, event, and sedimentary microfacies distributions. Additionally, the porosity and permeability of each microfacies in the reservoir model are quantitatively characterized based on statistics derived from porosity and permeability data of different strata, sedimentary microfacies, and rock facies in the study area. To demonstrate the superiority and reliability of this novel modeling method, a modeling case is presented. The case utilizes braided river unit elements as objects for the stochastic simulation of the target reservoir. The results of the case study highlight the advantages and robustness of the proposed modeling approach.