The CO2 methanation was studied over 7 wt.% nickel supported on Ce0.2Zr0.8O2/AC to evaluate the correlation of the structural properties with catalytic performance. The catalysts were investigated in more detail by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). A sample of 7 wt.% nickel loading supported on activated carbon (AC) was also prepared for comparison. The results demonstrated that the ceria-zirconia solid solution phase could disperse and stabilize the nickel species more effectively and resulted in stronger interaction with nickel than the parent activated carbon phase. Therefore, 7% Ni/Ce0.2Zr0.8O2/AC catalyst exhibited higher activity for CO2 reduction than 7% Ni//AC. It can attain 85% CO2 conversion at 350°C and have a CH4 selectivity of 100% at a pressure as low as 1 atm. The high activity of prepared catalysts is attributed to the good interaction between Ni and Ce0.2Zr0.8O2 and the high CO2 adsorption capacity of the activated carbon as well.
The methanation of carbon over nickel catalysts supported on activated carbon was investigated using a continuous flow microreactor. Catalysts with nickel loadings of 5, 7, and 10 % were synthesised by incipient wetness impregnation methods and characterised using Brunauer–Emmett–Teller (BET), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), H2-temperature-programmed reduction (TPR), BET, XRD, SEM, TEM and H2-TPR. The methanation reaction was studied over the temperature range 200–500°C with a H2 to CO2 ratio of 4 : 1 in He and at 1 atm. With an increase in Ni content from 5 to 7 % both conversion of CO2 and CH4 selectivity increased. Increasing the nickel content to 10 %, however decreased conversion and selectivity due to the larger crystallite size and lower surface area of the catalyst. The most active catalyst with 7 % Ni does not deactivate during 15 h time on stream at 350°C. The high catalytic activity and stability of the studied catalysts is a consequence of the reducibility of Ni and a synergetic effect between the nickel active sites and the activated carbon surface.
The adsorption and activation of carbon dioxide over copper cluster (Cu4) and copper doped on the alumina support (Cu4/Al2O3) catalytic systems have been investigated by using density functional theory and climbing image nudged elastic band. The adsorption energies, geometrical configurations, and electronic properties are analysed. The results show the strong chemical interaction between the copper cluster and the alumina support. Both the Cu4 cluster and Cu4/Al2O3 systems have a high adsorption ability for CO2, and the adsorption process is of chemical nature. The role of the alumina support in the adsorption and activation of CO2 has been addressed. The calculated results show that the “synergistic effect” between Al2O3 and Cu4 is the key factor in the activation of CO2.
1 September 2021 in Journal of Molecular Graphics and Modelling
Density functional theory (DFT) was used to calculate the step-by-step hydrogenation of carbon monoxide (CO) to form methanol over a Co4 cluster/Al2O3 surface. A three-dimensional Co4 tetrahedral structure was selected to explore its interaction with the supporting Al2O3 (104) surface. Co4 chemically reacted with Al2O3 to form a new chemical system. The calculated results show that Al2O3 support has strengthened the Co4 catalyst during the reaction since the formation of the Co–O bond. Loading Co4 on the Al2O3 surface increases CO adsorption ability but decreases the dissociation ability of C–O to produce hydrocarbons. As such, CH3OH formation becomes more favorable both kinetically and thermodynamically on Co4/Al2O3. In CO hydrogenation, methanol was synthesized through a CO reaction with hydrogen via either an Eley–Rideal or Langmuir–Hinshelwood pathway to form the intermediates C*-O-H, H-C*-OH, H2-C*-OH, and finally the hydrogenation of H2-C*-OH to methanol with both hydrogenation steps forming C*-OH and final product as rate-limiting. These results showed that the interaction between Co, Al2O3 and H2 pressure can change the pathway of CO hydrogenation on Co/Al2O3 and it may, therefore, influence distribution of the final products.