Melih State Papila

Prof. Melih State Papila

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 August 2017 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
SMShayan Mehraeen
Shayan Mehraeen
SGSelmiye Alkan Gürsel
Selmiye Alkan Gürsel
MPMelih State Papila
Melih State Papila
FCFevzi Çakmak Cebeci
Fevzi Çakmak Cebeci
Polyaniline nanofibers have shown promising electrical and electrochemical properties which make them prominent candidates in the development of smart systems employing sensors and actuators. Their electrochemical actuation potential is demonstrated in this study. A trilayer composite actuator based on polyaniline nanofibers was designed and fabricated. Cross-linked polyvinyl alcohol was sandwiched between two polyaniline nanofibrous electrodes as ion-containing electrolyte gel. First, electrochemical behavior of a single electrode was studied, showing reversible redox peak pairs in 1 M HCl using a cyclic voltammetry technique. High aspect ratio polyaniline nanofibers create a porous network which facilitates ion diffusion and thus accelerates redox reactions. Bending displacement of the prepared trilayer actuator was then tested and reported under an AC potential stimulation as low as 0.5 V in a variety of frequencies from 50 to 1000 mHz, both inside 1 M HCl solution and in air. Decay of performance of the composite actuator in air is investigated and it is reported that tip displacement in a solution was stable and repeatable for 1000 s in all selected frequencies.



Verified
Journal Article
Open access
PDF file
ARAbdul Bari Abdul raheman
Abdul Bari Abdul raheman
KBKaan Bilge
Kaan Bilge
MPMelih State Papila
Melih State Papila
This study investigates the effect of nanofiber interleaving on the mechanical performance of co-cured composite lap joints with effective fiber orientation mismatch at the joint interface. Joint configurations were defined by dominant yarn orientations at the bond line—denoted as (lower-substrate|upper-substrate)—and tested in (0|0), (90|90), and mismatched (0|90) setups using an 8-harness satin (8HS) fabric architecture, with and without nanofiber interlayers. Mechanical testing revealed an over ~25% reduction in lap shear strength for the (0|90) configuration relative to the matched (0|0) and (90|90) joints. Nanofiber interleaving effectively restored this loss, achieving strength levels comparable to the matched cases. Statistical analysis using two-way ANOVA and ANOM confirmed that both fiber orientation and nanofiber interleaving significantly influence joint strength, with a notable interaction effect (p < 0.001). Fractographic analysis further showed that nanofibers enhanced delamination resistance by stabilizing crack paths and suppressing crack jumps at crimping sites, especially in (0|90) joints where 0/90 yarn intersections are prone to early failure. These findings underscore the role of nanofiber interleaving in mitigating mismatch-induced failure mechanisms and improving the structural integrity of composite bonded interfaces.

7 September 2022 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
FAFarzin Asghari Arpatappeh
Farzin Asghari Arpatappeh
EMEmel Manga
Emel Manga
KBKaan Bilge
Kaan Bilge
BABerk Emre Aydemir
Berk Emre Aydemir
MGMehmet Ali Gülgün
Mehmet Ali Gülgün
MPMelih State Papila
Melih State Papila

15 November 2022 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
FAFarzin Asghari Arpatappeh
Farzin Asghari Arpatappeh
EMEmel Manga
Emel Manga
KBKaan Bilge
Kaan Bilge
BABerk Emre Aydemir
Berk Emre Aydemir
MGMehmet Ali Gülgün
Mehmet Ali Gülgün
MPMelih State Papila
Melih State Papila