This paper presents a time-to-digital converter/analog-to-digital-converter (TDC/ADC) hybrid LiDAR system-on-chip (SoC) to realize reliable self-driving systems. The smart accumulation technique (SAT) is proposed to achieve both 200-m and high-pixel-resolution range imaging, which was untrodden with conventional LiDARs. The “smart” accumulation is realized by a simple object recognition strategy with small circuit overhead. When compared to conventional accumulations, the LiDAR range is enhanced without degrading the pixel resolution. Moreover, a TDC/ADC hybrid architecture is proposed to achieve a wide-distance-range LiDAR with a small silicon area and short-range precision. To minimize the ADC cost, a residue-quantizing noise-shaping (RQNS) SAR ADC is proposed. The prototype LiDAR SoC is fabricated in the 28-nm CMOS technology and integrated into the silicon photomultiplier (SiPM)-based LiDAR system. LiDAR measured with 240 $\times$ 96 pixels at 10 frames/s achieves a measurement range of 200 m with a 70-klx direct sunlight: the measurement range is 2 $\times$ longer than conventional designs. Furthermore, our LiDAR achieves 4 $\times$ higher effective pixel resolution compared to conventional designs using simple accumulation. A 3-D point-cloud image acquired with a real-life environment is presented.
24 July 2019 in IEEE Journal of Solid-State Circuits
A voltage-controlled oscillator (VCO)-based comparator that automatically adapts its noise performance reflecting the input voltage difference ( $\Delta V_{\text {in}}$ ) is presented. Such adaptive operation significantly reduces the power of high-precision comparators in successive-approximation-register (SAR) ADCs. $\Delta V_{\text {in}}$ is integrated as a time difference via the VCO, where the integration continues as long as the time difference is below a certain threshold, defined by the phase detector deadzone. Thus, when $\Delta V_{\text {in}}$ is large, the comparator operates as a low-power delay line-based comparator, and with small $\Delta V_{\text {in}}$ , the VCO oscillates to integrate the input signal and suppresses the comparator noise. The required oscillations to complete the comparison are inversely proportional to $\Delta V_{\text {in}}$ , realizing fully adaptive noise and power scaling. This article provides a detailed analysis and specific design guidelines of the VCO comparator. Moreover, the PVT drift tolerance and detailed circuit implementations are deeply discussed as well. For proof-of-concept, a 13-bit SAR ADC with the proposed VCO-based comparator was fabricated in 65-nm CMOS. By off-chip LMS calibration, the ADC achieves peak SNDR 66 dB at 1 MS/s with a peak FoM of 29 fJ/conv.-step.
15 September 2020 in IEEE Journal of Solid-State Circuits
This article presents a 40-channel high-resolution automotive LiDAR system-on-chip (SoC), which utilizes the world's first dual-data converter (DDC). The proposed DDC consolidates the functions of ADC and TDC into a single circuitry and achieves acquisition of both high-precision time and voltage data from the input, realizing a 5x smaller analog front-end (AFE) area than prior arts. Such innovations lead us to a 40-channel AFE integration of the SoC without silicon cost increase, which characterizes our LiDAR system with 2x higher pixel resolution. To enhance the ADC's signal-to-noise and distortion ratio (SNDR) without sacrificing the area efficiency, a calibration-free and variation-tolerant voltage-controlled oscillator (VCO)-based ADC with a multiphase pulse density modulator (MP-PDM)-based feedback is proposed. Our proof-of-concept LiDAR system achieves a measurement range of 225 m at 70-klx direct sunlight, with a resolution of 240 x 192 pixels at 10 frames per second (FPS). To quantitatively measure the effect of the resolution improvement of our LiDAR, we evaluate the LiDAR's detection accuracy of small targets 75 m away. Due to the 2x higher vertical pixel resolution, our LiDAR can detect targets with 2x smaller height. The 3-D point cloud of the LiDAR captured outdoor in the wild is presented.
24 September 2024 in IEEE Journal of Solid-State Circuits
The rapid evolution of machine learning has led to the emergence of diverse neural network architectures, such as CNNs, Transformers, and their hybrid models, each with unique computational precision requirements. Transformers, in particular, demand higher precision compared to CNNs. Existing analog compute-in-memory (ACIM) solutions primarily cater to CNNs and struggle to achieve the high precision necessary for Transformers, despite their promise in addressing the memory bottleneck. To bridge this gap, we propose a capacitor-reconfigured CIM (CR-CIM) macro that introduces dual-mode operation, dynamically switching between high-precision and high-efficiency modes based on the active DNN layer. In the CNN mode, the CR-CIM employs bit-parallel computation and an 8-bit ADC to maximize power efficiency, exploiting the inherent error tolerance of CNNs. In contrast, for the Transformer mode, the CR-CIM switches to bit-serial computation and a 10-bit ADC to boost the compute signal-to-noise ratio (CSNR), ensuring the higher precision required by Transformers. This dual-mode functionality of the proposed CR-CIM is enabled by three key technologies: 1) a novel CR-CIM architecture and cell structure; 2) a resource-efficient multi-bit driver for bit-parallel computation; and 3) a software-analog co-design (SAC) strategy for enhanced Transformer computation. Our CR-CIM prototype is the first ACIM design to enable optimized operation for both Transformers and CNNs. CR-CIM achieves 45-dB signal-to-quantization-noise ratio (SQNR) and 31-dB CSNR (8-bit input and 8-bit weight bit-serial MAC) in the Transformer mode and a peak-power efficiency of 4094 TOPS/W (normalized to 1-bit ${\times } 1$ -bit MAC) in the CNN mode.
26 February 2014 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
A 0.3-0.8 V low-power 2-bit/step asynchronous successive approximation register analog-to-digital converter (ADC) is presented. A low-power 2-bit/step operation technique is proposed which uses dynamic threshold configuring comparator instead of multiple digital-to-analog converters (DACs). Power and area overhead is minimized by successively activated comparators. The comparator threshold is configured by simple Vcm biased current source, which keep the ADC free from power supply variations over 10%. Simple digital calibration is enabled by generating the reference internally. The prototype ADC fabricated in a 40 nm CMOS achieved a 44.3 dB signal-to-noise-plus-distortion ratio (SNDR) with 6.14 MS/s at a single supply voltage of 0.5 V. The ADC achieved a peak FoM of 4.8 fJ/conv-step at 0.4 V and operates down to 0.3 V.